Atari

Showing all 11 results

Greaseweazle V4
Greaseweazle V4 USB Floppy Adapter Flux Reader Writer

Greaseweazle v4 allows versatile floppy drive control over USB. By extracting the raw flux transitions from a drive, any disk format can be captured and analyzed - PC, Amiga, Amstrad, PDP-11, musical instruments, industrial equipment, and more. The Greaseweazle also supports writing to floppy disks, from a range of image file formats including those commonly used for online preservation (ADF, IPF, DSK, IMG, HFE, ...).

 

Greaseweazle V4 is the latest version, updated for mass production and with the following features:

  • Reads and writes 3", 3.5", 5.25", 8" disks (with suitable drive and cable)
  • Buffered outputs, for communicating with older 5.25" and 8" disk drives
  • Integrated power connector for directly powering most 3.5" disk drives
  • Write-enable jumper can be removed for safer preservation of precious vintage disks
  • Supports flippy-modded 5.25" drives
  • Supports Disk-Change detection as used by Rob Smith's integration into the WinUAE Amiga emulator
  • 3 user-definable outputs (eg. 8" interface REDWC signal)
  • 100% factory tested, and tested again by me before shipping

More information and documentation on the wiki page here:

This listing is for the Greaseweazle V4 device only. And does not include which you will require:

 
  • A disk drive (for example a PC 3.5" or 5.25" drive)
  • A floppy ribbon cable (typically you want a standard PC cable with 'twist' on pins 10-16, to communicate with a PC floppy drive)
  • Floppy drive power cable, or power supply
We don't offer any support for using this device. Built by Zero Flux Development.
19.42$ Excl. VAT Add to basket
Atari ST Gotek Grey STFM - STE
Atari ST Gotek Drive, OLED Display and FlashFloppy
Atari ST Gotek drive is a great replacement for your failing Atari ST floppy drive or you wish to simply replace it with a Gotek drive. These are plug and play in that you simply remove your existing Atari ST floppy drive and replace it with this unit. You will need a USB memory stick (NOT included) with your loaded .ST files. Want to know what a Atari ST Gotek drive is checkout this post It mentions Amiga but its no difference if its Amiga, Atari, Amstrad you will see the same benefits. Floppy Ribbon and Power Extender available as an option (10cm), If your existing ribbon is less than 7cm you may need the extender.    
37.82$ Excl. VAT Select options
Amiga Gotek Drive inc Amstrad, Spectrum, Atari, IBM PC
Gotek Drive pre-flashed with FlashFloppy (Generic)
Gotek drive is a inexpensive solution to replace your Commodore Amiga floppy drive (plus many other makes of computers). These are generic units that simply replace your existing floppy drive or put in an external enclosure. The Gotek drive is pre flashed with FlashFloppy which allows it not only to work with the Commodore Amiga, but also Amstrad CPC computers*, Sinclair Spectrum*, Atari and DOS / IBM PC's* You will need a USB memory stick (NOT included) with your loaded ADF files. This Gotek drive will work with all Commodore Amiga computers including:
  • Amiga A500
  • Amiga A500 Plus
  • Amiga A600
  • Amiga A1200
  • Amiga A1000
  • Amiga A1500
  • Amiga A2000
  • Amiga A3000
  • Amiga A4000
  • Amiga 4000T
You can also choose from a selection of add-ons below which include
  • OLED Display instead of the 3 Digit Display
  • Internal Gotek Speaker to hear those floppy sounds!
  • Gotek Rotary knob for easily selecting that game, app or demo
  We also sell Amiga Gotek Drives with 3D printed mounts that fit neatly in your Amiga: Amiga A500 Internal Gotek Drive with OLED Display Amiga A500 Plus Gotek Drive with OLED Display Amiga A600 Internal Gotek Drive with OLED Display Amiga A1200 Internal Gotek Drive with OLED Display   What are gotek drives in detail? Read here What is FlashFloppy? Check out this link Want to know even more about them, checkout retro32.com's review of them here Also checkout one of our favorite youtube streamers TheGebs24 and her views on the Gotek drive!   *Amstrad / Spectrum or computers with 3" disk drives or old PCs with 5.25" drives and such. You just need the correct floppy IDE or Ribbon connection cables NOT INCLUDED.
33.73$ Excl. VAT Select options
Atari Lynx Recapping Service
Atari Lynx Recapping Service MK 1 or MK 2
Atari Lynx recapping service for either the Atari Lynx MK 1 or Atari Lynx MK 2 (AKA Atari Lynx 2). Recapping service includes replacing all electrolytic capacitors of which there are approx 20 depending on the version. Note this is not a repair service.
Overseas recapping orders
Overseas orders are very welcome and we are able to provide you return shipping costs at the checkout. To do this add any of our recapping services to your shopping basket and then at the checkout simply fill in the billing and shipping form including your telephone and email address (important) and click the 'Request a quote' link. You will receive an email within 24hrs with the shipping cost and you can then proceed with the order by clicking on the 'Complete your order' within the email. There is no need to leave the checkout page open your web browser.    
30.66$ Excl. VAT Add to basket
Atari Falcon - Fully Refurbished
Refurbished Atari Falcon 030 Computer

Refurbished Atari Falcon 030.

Technical Specifications
  • Motorola 68030 (16Mhz) CPU
  • 14Mb Ram
  • 3.5" 1.44mb Floppy Drive
  • UK Layout Keyboard
What’s included?
  • Professionally refurbished Atari Falcon inc Power lead
  • Original Atari STM-1 Mouse.
  What is Refurbished? The Atari Falcon mainboard has been professionally recapped deep cleaned using a Ultrasonic cleaner, bathed using deionised water and professional grade PCB/Flux cleaning solution. Once completed it is dried and a full diagnostic test is completed. Each unit is thoroughly inspected and tested including:
  • Full Keyboard check.
  • Floppy drive read and write test.
  • Sound checked.
  • Video checked.
  • Case and keyboard is stripped and cleaned.
  What is Ultrasonic cleaning? Ultrasonic cleaning is a process that uses ultrasound (usually from 20–40 kHz) to agitate a fluid, this fluid is made up for this specific job which is to clean and remove any flux left over from recapping. We use deionised water (deionized depending where your from) and professional grade PCB cleaner. An example of the results: [caption id="attachment_17767" align="aligncenter" width="300"] Amiga Motherboard Before being Recapped & Ultrasonic Cleaned[/caption]   [caption id="attachment_17766" align="aligncenter" width="300"] Refurbished Amiga Motherboard - Recapped & Ultrasonic Cleaned[/caption]   Add-ons - Modifications  We are able to offer extras and modifications, please contact us with your requirements.   Shipping Worldwide shipping available simply contact us for a shipping quote.   Images of the Atari Falcon for illustrative purposes only, each unit will show signs of age and use.
3,065.96$ Excl. VAT Add to basket
Atari 1040 STFM Refurbished
Refurbished Atari 1040 STE

Refurbished Atari 1040 STE.

Technical Specifications
  • Motorola 68000 (8Mhz) CPU
  • 4Mb Ram (Standard)
  • 3.5" 1.44mb Floppy Drive
  • UK Layout Keyboard
  • TOS V1.62
What’s included? Professionally refurbished Atari 1040 STE inc Power lead (power cable will have correct plug depending on where its being sent). NOTE Cases may have a 520 STE Badge but all our Atari STE's will have 4Mb of ram minimum.   What is Refurbished? The Atari STE mainboard has been professionally recapped deep cleaned using a Ultrasonic cleaner, bathed using deionised water and professional grade PCB/Flux cleaning solution. Once completed it is dried and a full diagnostic test is completed. Each unit is thoroughly inspected and tested including:
  • Full Keyboard check.
  • Floppy drive read and write test.
  • Sound checked.
  • Video checked.
  • Case and keyboard is stripped and deep cleaned.
We also perform the following mandatory Atari STE fixes:
  • Motherboard Recapped (all electrolytic capacitors)
  • PSU Recapped.
  • 10K pull up resistor network to the DMA databus.
  • 1772 Pull up Resistors added.
  • STE video circuit recapped.
  • STE Reset fix 22uF added across C100.
  • Bus resistors replaced with 2.2k resistor arrays.
  What is Ultrasonic cleaning? Ultrasonic cleaning is a process that uses ultrasound (usually from 20–40 kHz) to agitate a fluid, this fluid is made up for this specific job which is to clean and remove any flux left over from recapping. We use deionised water (deionized depending where your from) and professional grade PCB cleaner. An example of the results: [caption id="attachment_17767" align="aligncenter" width="300"] Amiga Motherboard Before being Recapped & Ultrasonic Cleaned[/caption]   [caption id="attachment_17766" align="aligncenter" width="300"] Refurbished Amiga Motherboard - Recapped & Ultrasonic Cleaned[/caption]   Worldwide shipping available simply contact us for a shipping quote.    Images of the Atari STE for illustrative purposes only, each unit will show signs of age and use.
355.78$ Excl. VAT Add to basket
Atari STe Recapping Service
Atari 520 STe / 1040 STe / 4160 STe Recapping Service inc PSU
Atari 520 STe / 1040 STe / 4160 STe recapping service including recapping of STe PSU, all board revisions. This service includes both recapping of the Atari STe motherboard and PSU.
  • Check of the STe motherboard and PSU before recapping is begun.
  • Removal of existing capacitors.
  • Clean-up and preparation of area.
  • Replace using Panasonic/Wurth/KEMET capacitors.
  • Retest (Video, Audio, Floppy Boot) using diagnostic cartridge.
We also provide a recapping service for the  Atari STF / STFM   What do you need to send? All we need is the mainboard and PSU, so please only send the board and PSU in its metal shielding. If however you choose to send the whole unit, there is an option to do that also via the choices below.  
66.45$ Excl. VAT Add to basket
Atari 1040 STFM Refurbished
Refurbished Atari 1040 STFM

Refurbished Atari 1040 STFM.

Technical Specifications
  • Motorola 68000 (8Mhz) CPU
  • 1Mb Ram (Standard)
  • 3.5" 1.44mb Floppy Drive
  • UK Layout Keyboard
  • TOS V1.02
What’s included? Professionally refurbished Atari 1040 STFM inc Power lead (power cable will have correct plug depending on where its being sent). NOTE Cases may have a 520 STFM Badge but all our Atari STFM will have 1Mb of ram minimum.   What is Refurbished? The Atari STFM mainboard has been professionally recapped deep cleaned using a Ultrasonic cleaner, bathed using deionised water and professional grade PCB/Flux cleaning solution. Once completed it is dried and a full diagnostic test is completed. Each unit is thoroughly inspected and tested including:
  • Full Keyboard check.
  • Floppy drive read and write test.
  • Sound checked.
  • Video checked.
  • Case and keyboard is stripped and cleaned.
We also perform the following mandatory Atari STFM fixes:
  • PSU Recapped.
  • 10K pull up resistor network to the DMA databus.
  • 1772 Pull up Resistors added.
  • STFM video circuit recapped.
  • STFM Reset fix 22uF added across C100.
  • Bus resistors replaced with 2.2k resistor arrays.
  What is Ultrasonic cleaning? Ultrasonic cleaning is a process that uses ultrasound (usually from 20–40 kHz) to agitate a fluid, this fluid is made up for this specific job which is to clean and remove any flux left over from recapping. We use deionised water (deionized depending where your from) and professional grade PCB cleaner. An example of the results: [caption id="attachment_17767" align="aligncenter" width="300"] Amiga Motherboard Before being Recapped & Ultrasonic Cleaned[/caption]   [caption id="attachment_17766" align="aligncenter" width="300"] Refurbished Amiga Motherboard - Recapped & Ultrasonic Cleaned[/caption]   Worldwide shipping available simply contact us for a shipping quote.    Images of the Atari STFM for illustrative purposes only, each unit will show signs of age and use.
Read more
Atari Falcon Recapping
Atari Falcon Recapping Service inc PSU
Atari Falcon recapping service including recapping of  PSU, all board revisions. This service includes both recapping of the Atari Falcons' motherboard and PSU.
  • Check of the Falcon motherboard and PSU before recapping is begun.
  • Removal of existing capacitors.
  • Clean-up and preparation of area.
  • Replace using Panasonic/Wurth/KEMET capacitors.
  • Retest (Video, Audio, Floppy Boot) using diagnostic cartridge.
We also provide a recapping service for the  Atari 520 STe / 1040 STE / 4160 STE   What do you need to send? All we need is the mainboard and PSU, so please only send the board and PSU in its metal shielding. If however you choose to send the whole unit, there is an option to do that also via the choices below.  
66.45$ Excl. VAT Add to basket
Atari STe Recapping Service
Atari 520 STFM / 1040 STFM Recapping Service inc PSU
Atari 520 STFM / 1040 STFM recapping service including recapping of STFM PSU, all board revisions. This service includes both recapping of the Atari STFM motherboard and PSU.
  • Check of the STFM motherboard and PSU before recapping is begun.
  • Removal of existing capacitors.
  • Clean-up and preparation of area.
  • Replace using Panasonic/Wurth/KEMET capacitors.
  • Retest (Video, Audio, Floppy Boot) using diagnostic cartridge.
We also provide a recapping service for the  Atari 520 STe / 1040 STE / 4160 STE and Atari 520 STF / Atari 1040 STF   What do you need to send? All we need is the mainboard and PSU, so please only send the board and PSU in its metal shielding. If however you choose to send the whole unit, there is an option to do that also via the choices below.  
61.33$ Excl. VAT Add to basket
Atari STe Recapping Service
Atari 520 STF / 1040 STF Recapping Service inc PSU
Atari 520 STF / 1040 STF recapping service including recapping of STF PSU, all board revisions. This service includes both recapping of the Atari STF motherboard and PSU.
  • Check of the STF motherboard and PSU before recapping is begun.
  • Removal of existing capacitors.
  • Clean-up and preparation of area.
  • Replace using Panasonic/Wurth/KEMET capacitors.
  • Retest (Video, Audio, Floppy Boot) using diagnostic cartridge.
We also provide a recapping service for the  Atari 520 STe / 1040 STE / 4160 STE   What do you need to send? All we need is the mainboard and PSU, so please only send the board and PSU in its metal shielding. If however you choose to send the whole unit, there is an option to do that also via the choices below.  
61.33$ Excl. VAT Add to basket