A1200 Upgrades

Greaseweazle v4.1 Amiga Amstrad, Spectrum
Greaseweazle V4.1 USB Floppy Adapter Flux Reader Writer

Greaseweazle v4.1 allows versatile floppy drive control over USB. By extracting the raw flux transitions from a drive, any disk format can be captured and analysed - PC, Amiga, Amstrad, PDP-11, musical instruments, industrial equipment, and more. The Greaseweazle also supports writing to floppy disks, from a range of image file formats including those commonly used for online preservation (ADF, IPF, DSK, IMG, HFE)

 

Greaseweazle V4.1 is the latest version, updated for mass production and with the following features:

  • Reads and writes 3", 3.5", 5.25", 8" disks (with suitable drive and cable)
  • Buffered outputs, for communicating with older 5.25" and 8" disk drives
  • Integrated power connector for directly powering most 3.5" disk drives
  • Write-enable jumper can be removed for safer preservation of precious vintage disks
  • Supports flippy-modded 5.25" drives
  • Supports Disk-Change detection as used by Rob Smith's integration into the WinUAE Amiga emulator
  • 3 user-definable outputs (eg. 8" interface REDWC signal)
  • 100% factory tested, and tested again by me before shipping

More information and documentation on the wiki page here:

This listing is for the Greaseweazle V4.1 device only. And does not include which you will require:

 
  • A disk drive (for example a PC 3.5" or 5.25" drive)
  • A floppy ribbon cable (typically you want a standard PC cable with 'twist' on pins 10-16, to communicate with a PC floppy drive)
  • Floppy drive power cable, or power supply
  Built by Zero Flux Development. And yes this is the item mentioned on Tom's Hardware: https://www.tomshardware.com/news/raspberry-pi-emulates-amiga-1200-uses-real-floppy-disks  
£22.49 Ex. VAT Read more
Replacement Amiga 500 PSU (Brand New)
Commodore Amiga PSU for A1200
Commodore Amiga PSU for A1200, these are brand new and modern with It's 50W (55W peak) of total combined output power making it nearly 2x times stronger than original Commodore Amiga PSU and 2x smaller in dimensions & weight.
Key features:
  • Stabilized & filtered 5VDC up to 4A output (4.4A peak)
  • Stabilized & filtered 12VDC up to 2A output (2.2A peak)
  • Stabilized & filtered -12VDC up to 0.5A output (0.55A peak)
  • Carefully calibrated for Amiga 500 reference load
  • Active & passive over voltage protection for main +5VDC line
  • Over current protection for all output lines
  • Fully isolated & fused on AC side
  • Power On/Off switch
  • Long output cable (1.8m) with rectangular DIN 5-pin plug.
  • Detachable input AC cable for all versions (cable included)
  • Weight only 0.4 KG (2x less than original PSU)
  • Runs COLD!
  • Safety standards: UL60950-1, TUV EN60950-1, ANSI/AAMI ES60601-1, TUV EN60601-1, IEC60601-1
  • Manufactured by Electroware
  • UK Stock
 
Warning! Risk of electrical shock and energy hazard when opened. All failures should be examined by a qualified technicians only. Risk of fire or electrical shock. The ventilation holes should be protected from foreign objects or dripping liquids. Please do not install power supplies in places with high ambient temperature or close to the heat source. Enclosed power supplies are intent to work in indoor locations, it's not allowed to use power supplies outdoor, in dust or high moisture. Output current and output wattage must not exceed the rated values. This replacement Amiga PSU has been designed for Commodore Amiga 1200 vintage computer systems only and should be considered as an integral component of Amiga computer system. Do not connect to any other devices as it's not a general purpose PSU. Manufacturer is not responsible for any consequences of unauthorised or arbitrary repairs, modifications or incorrect usage. Please notice that new, properly working replacement Amiga PSU is reducing the system's potential fail rate but still is not guaranteeing that entire Amiga system will work correctly (it's >30 years old).    
£45.83 Ex. VAT Read more
PiStorm32-Lite for Amiga A1200
PiStorm32 Lite A1200 with RPi 3A+, 64Gb SD Card
PiStorm32-Lite A1200 is the full package which includes:  
  • PiStorm32-Lite A1200 Adaptor
  • Raspberry Pi 3A+ Module
  • 64Gb SD Card (Pre-installed kernel with EMU68) You will need a copy of Workbench 3.0 or above and a kickstart rom again 3.1 or above or send us an SD image and we will install and setup FOC.
  • 3D printed RPi header protector
  Once installed and setup you will have an implementation of MC68020/030/040 with FPU support, coupled with a fast implementation of the Emu68 CPU unit (Emu68 is a JIT emulator) written by Michal Schulz, thanks to it the system boots in a few seconds. Extra functionality is added (thanks to an additional RPi 3A+ module) with an HDMI port, so you can have Full HD video and around 340MB of Fast Ram.   Check out this video by Capt. LeChuck, Pistorm32-Lite with EMU68K   [kad_youtube url="https://www.youtube.com/watch?v=8BBU48cLuUc&t=109s" ]   We also just sell the Pistorm32-Lite adaptor here, just add you own Raspberry Pi and SD Card.  
  NOTE: This is a open source project and will require some knowledge of the Amiga. The PiStorm adaptors are professionally manufactured, and a contribution to the developer is made.    
£124.99 Ex. VAT Select options
PiStorm32-Lite for Amiga A1200
PiStorm32 Lite for Amiga A1200 Adaptor Only
PiStorm32 Lite Adaptor for the Amiga A1200 is designed to connect one of the Raspberry Pi's listed below (not included) NOTE: We do sell a plug and play package here which includes PiStorm32-Lite, Raspberry Pi 3A & SD Card. Once you add your own Raspberry Pi, setup an SD card and plug it in the trapdoor of the A1200 like all A1200 accelerators (TF1230 or TF1260) you will have an accelerated Amiga 1200!   Compatible Rasperry Pi's:
  • Raspberry Pi 3A
  • Raspbery Pi 3B
  • Raspberry Pi 4B
  Want to know more about the PiStorm check out the following link: https://github.com/PiStorm/pistorm32-lite-hardware   Compatible Rasperry Pi's:
  • Raspberry Pi 3A
  • Raspbery Pi 3B
  • Raspberry Pi 4B
  With the Pistorm32-lite the A1200 can go up to a 68040 and using a Pi4 you could see 2000 Plus Mips! Want to know more about the PiStorm check out the following link: https://github.com/PiStorm/pistorm32-lite-hardware   The PiStorm adaptors are professionally manufactured. and a contribution to the developer is made to support this project.      
£70.83 Ex. VAT Read more
Amiga PSU Boost A500 - A500 Plus
Commodore Amiga PSU for A1200 (BOOST VERSION)
Commodore Amiga PSU for A1200 BOOST VERSION, up to 8A at 5VDC strong, adjustable PSU for regular and accelerated Commodore Amiga A500, A500+, A600, A1200. The new Amiga PSU BOOST is a modern, 50W strong replacement power supply unit for Commodore Amiga computer systems. Based on our famous Amiga DUO/DUO+ PSU experiences provides stable, filtered, adjustable 5VDC (up to 8.0A), 12VDC (up to 0.5A) and -12VDC (up to 0.15A) by industrial grade components. Now your Vampire, Blizzard, ACA or Furia accelerator will get enough juice to work flawlessly with full MHz clocks. Factory trimmed for stock Amiga 500 reference load, may be adjusted to give exact 5VDC with 2-3x heavier loads.
Key features:
  • Commodore Amiga 500, 500+, 600, 1200 compatible
  • Stabilized & filtered 5VDC up to 8A output (peak)
  • Stabilized & filtered 12VDC up to 0.5A output
  • Stabilized & filtered -12VDC up to 0.15A output
  • 5VDC manual adjustment feature (potentiometer)
  • Factory calibrated for stock Amiga 500 reference load
  • Active & passive over voltage protections for main +5VDC line
  • Over current protection for all output lines
  • Integrates Protection & Adjustment LED Module add-on
  • Fully isolated & fused on AC side
  • Durable power On/Off switch (black)
  • Status LED (Good Status Green)
  • Long output cable (1.8m) with rectangular DIN 5-pin plug
  • Detachable input AC cable for all versions (cable included)
  • Weight only 0.4 KG (2x less than original PSU)
  • UK Stock
 
Warning! Risk of electrical shock and energy hazard when opened. All failures should be examined by a qualified technicians only. Risk of fire or electrical shock. The ventilation holes should be protected from foreign objects or dripping liquids. Please do not install power supplies in places with high ambient temperature or close to the heat source. Enclosed power supplies are intent to work in indoor locations, it's not allowed to use power supplies outdoor, in dust or high moisture. Output current and output wattage must not exceed the rated values. This replacement Amiga PSU has been designed for Commodore Amiga 1200 vintage computer systems only and should be considered as an integral component of Amiga computer system. Do not connect to any other devices as it's not a general purpose PSU. Manufacturer is not responsible for any consequences of unauthorised or arbitrary repairs, modifications or incorrect usage. Please notice that new, properly working replacement Amiga PSU is reducing the system's potential fail rate but still is not guaranteeing that entire Amiga system will work correctly (it's >30 years old).  
£70.83 Ex. VAT Read more
Amiga Gotek FlashFloppy OLED Header
Amiga 1200 Gotek Drive (Flashfloppy) with Mount, OLED Header
Amiga 1200 Gotek drive pre-installed with FlashFloppy, these Gotek drives are based on a more modern OpenFlops floppy emulator which provides many improvements over the original Gotek drive, these units are a great replacement for your failing Amiga 1200 floppy drive or you wish to simply replace your current 3.5" floppy drive. These are plug and play in that you simply remove your existing Amiga 1200 floppy drive and replace it with this unit (you use your existing bracket). 3 new screws will also be supplied to secure it to the Amiga 1200. The Amiga 1200 Gotek drive also comes with an OLED Header unit will need 4 wires passing through the vent, the end plastic boots will be supplied so you add them after you have passed them through the vent. This provides easy viewing of what game or program you wish to use. You will need a USB stick (any size) formatted as FAT32. You can add a pre-configured USB stick as an option below.
What's included:
  • OpenFlops Gotek Drive
  • 3D Printed Amiga 1200 Gotek Mount
  • OLED Display with 3D Printed Header
[hr]
What is OpenFlops Gotek Drive?
OpenFlops is an Open Hardware implementation of such an emulator, inspired from the ubiquitous Gotek hardware. It is designed to run the FlashFloppy firmware, which gives it several improvements over the original Gotek: Further information on what a gotek drive is can be found here    
£37.49 Ex. VAT Read more
Amiga A1200 HDISK/FDISK LED Adaptor
Amiga A1200 HDISK/FDISK LED Adapter
Amiga A1200 HDISK/FDISK LED adapter provides 2 separate inputs to show the activity of and not limited to, Icedrake V4, PiStorm32-Lite SD slot, hard drives or PCMCIA port using the original LED module on the Amiga 1200 LED panel. Signals for the internal HDD and DISK are transmitted as is, also this module corrects the constant LED light that may occur with some SD or CompactFlash cards. There are also LEDs on the module itself that show floppy and hard drive activity. This can be especially useful when the Amiga 1200 is operated without the original keyboard. Configuration  There are a total of 2 pins available on  J3  , which have the following characteristics.
  • A  = HDD input - (output via HDISK LED)
  • B  = FDD input - (output via FDISK LED)
  So for example you want to show the PCMCIA activity, you would connect a wire to the FDD input and any PCMCIA activity will show via the FDISK LED.   NOTE: Soldering skills will be required when connecting 3rd party activity signals to the Amiga A1200 HDISK/FDISK LED adapter, more details to follow.  
£10.83 Ex. VAT Read more
FlashFloppy Gotek OLED Display Header
Amiga 600/1200 Gotek OLED Display Header Only
*This unit is if you already have a FlashFloppy Gotek drive. The Amiga 600/1200 FlashFloppy OLED header unit is the perfect companion for the Amiga 600/1200 Gotek FlashFloppy. It allows easy viewing the current ADF file loaded on the Gotek. This requires zero hacking of your Amiga case. These units are ready built and are very easy to install. What you will receive:
  • 3D Printed Header
  • OLED Display
  • 30cm of cable from the header to the Gotek drive.
£11.66 Ex. VAT Read more
TF1230 Accelerator Amiga 1200 - Terriblefire
TF1232 Amiga Accelerator 64Mb
TF1232 Amiga Accelerator - Terriblefire for the Amiga 1200 which hosts a 68030 processor running at 50Mhz coupled with 128mb of fast ram. This card is a perfect add-on for the Amiga A1200 and is the sweet spot between cost and speed.This card is a perfect add-on for the Amiga A1200 and is the sweet spot between cost and speed. And is the next step up after the 11Mb Ex1T Fast Ram or if your budget does not quite stretch to the Terriblefire TF1260, the TF1230 A1200 card is the perfect add-on and you will notice a huge speed difference.
  • 68030 'Gold' CPU running at 50MHZ (NOT OVERCLOCKED) with MMU
  • 64Mb Fast Ram
  • IDE Interface - Driver required - ehide.device or purchase our AmigaOS 3.2 Rom with ehide.device built in (uploading of AmigaOS purchase evidence required)
  • Fits in your old/new stock A1200 case!!!
 
Prerequisites 
  • Timing fix is strongly recommended on your A1200 motherboard. We can do this free of charge if you send your board to us (return shipping does need to be covered).
  • Kickstart ROM 3.1, 3.1.4, 3.2, 3.x or 3.9 (not compatible with 3.0).
  • Some boards do not have a chamfered edge on the connector (1A and 1B boards) which may bend the connector pins, if your unsure please ask.
 
What is TerribleFire?
Well it's not what it's who, and that person is Stephen Leary who has designed a whole host of accelerators and ram cards for the Amiga A500, A1200 and Amiga CD32. These include many but the most common ones are:    
£158.33 Ex. VAT Read more
Bifrost A1200 Heimdall Edition
BIFROST A1200 Heimdall Edition LED Replacement
Bifrost A1200 Heimdall Edition board is a direct keyboard LED replacement board for your Amiga 1200 computer. It uses some of the latest cutting edge technology to bring you an updated, fully feature packed and highly customisable cosmetic experience for your beloved retro computer, available literally at your fingertips. Customize the POWER-, FLOPPY- and HARDDRIVE LEDs to any colours and brightness of your choice using the LEDs themselves as programming buttons. You can also choose from pulsating effects as well as colour cycling effects. Each channel comes with three LEDs and all LEDs are individually programmable. All in all you will find that the A1200 Bifrost, can deliver over 150 million colour and brightness combinations to EACH channel making the Bifrost a great choice for putting that personal touch to your Amiga machine. The Bifrost also supports PCMCIA signal and/or up to three custom devices on separate input channels, utilizing a secondary indicator layer on each of the LED rows. Furthermore, it supports the new CAPS LOCK Bifrost module not allowing for any original lights to escape user customization.   What's included:
  • 1x A1200 Bifrost, Heimdall Edition
  • 1x A1200 CL Module
  • 1x 30cm 4-lead connection wire
  • 1x 30cm 1-lead connection wire
  • 1x Bleed Shield
  • 1x Diffuser Holder
  • 6x Normal Diffusers (3x for T1-, 3x for T2-cases)
  • 6x Tall Diffusers (3x for T1-, 3x for T2-cases)
  • 1x DIY PCMCIA enabling kit
  Below are a couple of videos demonstrating what you can achieve:  
A1200 Bifrost, Heimdall Edition - Demo
[kad_youtube url="https://youtu.be/xSmitjyRTaE" ]    
BIFROST A1200 Heimdall Edition - Advanced Mixing
[kad_youtube url="https://youtu.be/qa4u2WIjMVw" ]   These units will fit any Amiga 1200 case including the A1200.NET cases we sell. Full manual on fitting and setting up is available here   Photo credits: Conny Larsson  - Product image Johnnathan Taylor  
£66.66 Ex. VAT Read more
Amiga 1200 Gotek, FlashFloppy, 3D Printed Mount
Amiga 1200 Gotek Drive, Printed Mount, OLED Display and FlashFloppy
Amiga 1200 Gotek drive is a great replacement for your failing Amiga 1200 floppy drive or you wish to simply replace it with a Gotek drive. These are plug and play and come pre flashed with FlashFloppy in that you simply remove your existing floppy drive and replace it with this unit (you use your existing bracket). 3 new screws will also be supplied to secure the Gotek drive to your Amiga. You will need a USB memory stick (NOT included) with your loaded ADF files but we offer an option for a pre-configured USB stick below.
What are ADF files?
ADF files is the standard Amiga Disk Format for floppy disk images. no different to Sega or Nintendo roms, ADF's are images of Amiga floppy disk games. Not only could you have access to a huge back catalogue of retro Amiga games, but there are still brand new games being released today, for example: Raid over Moscow or Bridge Strike these are all available as ADF files. But you not limited to games or programs, but you have access to tons of Amiga demos (if your into that scene).
What are gotek drives in detail? Read here What is FlashFloppy check out this link Want to know even more about them, checkout retro32.com's review of them here Also checkout one of our favorite youtube streamers TheGebs24 and her views on the Gotek drive!
£33.33 Ex. VAT Read more
ScanPlus AGA Amiga 1200/4000D
ScanPlus AGA – Amiga 1200 and Amiga 4000D Scandoubler
ScanPlus AGA is a internal Scandoubler for the Amiga 1200 and Amiga 4000D (not Amiga 4000T or Amiga CD32). The advantage of the internal ScanPlus AGA is that it will allow you to connect to a standard VGA monitor whether that be a traditional (best) CRT experience or a flat screen monitor or TV with VGA connector. The primary PCB sits over the Lisa chip and the smaller PCB sits over the Alice chip. Output connector connects to a VGA socket which sits in a 3D printed backplate which is included (available in white or black, please note white will be sent if no note is made asking for black). ScanPlus is plug and play, no drivers or setting up required, it will work straight out of the box, all Amiga screen modes are available via the VGA connector, these include Multiscan, PAL, NTSC, DoublePAL DoubleNTSC, Euro36, Euro72, Super72. It provides smooth 50-60 Hz and up to 24 bit colour depth. What's included:
  • ScanPlus AGA (Lisa and Alice PCB's).
  • VGA breakout socket.
  • White Backplate for VGA socket (please but a note on the order to ask for Black if required instead).
  • Ribbon cable to connect to VGA socket.
  • Link cable to Alice PCB.
  • DPMS screensaver utility included - Download here
  • Item is brand new.
  • Installation guide is here
 

Note:

  • Not retail boxed.
  • Requires some knowledge of Amiga hardware when installing, fitting service available if required, ask for details.
£0.00 Ex. VAT Read more