ACA1234 Amiga A1200 Accelerator 68030 128Mb Fast Ram
ACA1234 Amiga A1200 accelerator is the latest 68030 CPU based card from Individual Computers. This is far more than just another 68030 accelerator, it adds high-speed mass storage, MPAROM and many other improvements.
X-Surf 100 for all Commodore Amigas with Zorro Slots
X-Surf 100 is a networking card for all Amiga computers with Zorro slots. For the Amiga A2000 or Zorro-daughterboards for the A1200, it will run at Z2 speed. If installed in an Amiga A3000, A4000 or the respective tower versions, it will run at Z3 speeds, which is up to five times faster than Z2.
Key features:
- 100MBit physical link rate
- Sana-II device for use with OS2.0 up to OS3.9
- Officially supported in the Linux-m68k kernel
- Space- and power-saving design
- Gold plated Zorro contacts and stainless steel metal bracket
- Local expansion port for our high-speed USB module “RapidRoad”
Drivers can be downloaded from here.
Manual here
Wiki here
Requirements:
- TCP/IP stack such as Miami DX, AmiTCP, Genesis (included in OS3.9) or Roadshow
- Sufficient RAM and 68020 CPU or higher
- Kickstart/Workbench 2.0 or higher
- File transfer method for drivers to be transferred to the Amiga
Transfer rates of over 1600kBytes/s have been measured with the X-Surf-100. Please note that the classic Amiga architecture and the current TCP/IP stacks for the Amiga don’t allow saturating a 100MBit Ethernet link. Performance in your system may be slower due to CPU performance and programs running in multitasking.
Please note that we cannot guarantee the X-Surf-100 to work in third-party Zorro boards as used in tower conversions, such as boards made by Eagle, Mikronik, RBM or Elbox. The X-Surf-100 may or may not work in these boards. Although the bus interface is designed to tolerate many mistakes that the vendors of those third-party boards have made, we can only guarantee proper operation in original Commodore daughter boards. Should the card fail to work in such a third-party board, you may have to close the Z2 jumper and downgrade to Z2 speed. For operation in Z3 computers, the Buster-11 chip is recommended. If there is only one DMA master in the Z3 system, a Buster-9 may also be used.
Owners of the Merlin graphics card must have the latest hardware patches installed. Owners of the Mediator PCI/Zorro daughterboard must close the “swap” jumper.
The X-Surf-100 is officially supported in the Linux-m68k kernel.
A630 Rev 3 Accelerator 68030 50Mhz, 64Mb, FPU Amiga A600 PURPLE
A630 Rev 3 68030 50Mhz inc FPU Amiga A600 PURPLE EDITION is the latest revision of the A630 modern turbo card with the classic 68030 Motorola processor running at 50Mhz and also includes an onboard FPU. Perfect for that sweet spot in speed and usefulness for Demos, WHDLoad* gaming, internet and so on. This will give any A600 a great speedboost in a compact unit.
Full specs:
- CPU MC68030, clocked on 50MHz.
- FPU 68882FN40 – synchronous or asynchronous clocking.
- 64MB SDRAM Fast Ram.
- Cooling: Active included.
- PCMCIA Friendly.
- PCB Colour – Purple
Important Information:
MMULib’s for the A630 Accelerator
The A630 Accelerator requires the installation of MMULib’s and it very important you use the right ones for the kickstart ROM you are using:
3.1 Kickstart:
http://main.aminet.net/util/libs/MMULib.lha
http://main.aminet.net/util/libs/MMULib.readme
3.2, 3.2.1 or 3.2.2
Install the MMULib package that came with the installation CD ONLY and NOT the ones from Aminet.
Notes:
- Some demos or games may require disable “CPU CACHE” for better compatibility with the MC68000.
- The card is designed to work with 3.1 Roms and above including 3.2 and 3.2.1 of which can be purchased below.
- An internal HDD/CF/SD Card needs to be installed for the A630 to boot.
*2Mb Chip ram is strongly recommended for WHDLoad which is available here
Sinclair ZX Spectrum 16K/48K Recapping Service
Sinclair ZX Spectrum recapping service, the following models are covered using this service:
- Sinclair ZX Spectrum 48k
- Sinclair ZX Spectrum+ (Plus)
This is not a repair service but a maintenance service and boards should be in working order.
What’s included?
- Check of the board before recapping is begun.
- Removal of existing capacitors (radial capacitors).
- Cleanup and preparation of area.
- Replace using tier one capacitors.
- Retest (Video, Audio)
Whole units can be sent (no need to send just the motherboard).
Atari 520 STe / 1040 STe / 4160 STe Recapping Service inc PSU
Atari 520 STe / 1040 STe / 4160 STe recapping service including recapping of STe PSU, all board revisions. This service includes both recapping of the Atari STe motherboard and PSU.
- Check of the STe motherboard and PSU before recapping is begun.
- Removal of existing capacitors.
- Clean-up and preparation of area.
- Replace using Panasonic/Wurth/KEMET capacitors.
- Retest (Video, Audio, Floppy Boot) using diagnostic cartridge.
We also provide a recapping service for the Atari STF / STFM
What do you need to send?
All we need is the mainboard and PSU, so please only send the board and PSU in its metal shielding. If however you choose to send the whole unit, there is an option to do that also via the choices below.
Amiga CD32 FMV Recapping Service
CD32 FMV recapping service, all board revisions. NOTE this is NOT a repair service.
Overseas recapping orders
Overseas orders are very welcome and we are able to provide you return shipping costs at the checkout.
To do this add any of our recapping services to your shopping basket and then at the checkout simply fill in the billing and shipping form including your telephone and email address (important) and click the ‘Request a quote‘ link.
You will receive an email within 24hrs with the shipping cost and you can then proceed with the order by clicking on the ‘Complete your order‘ within the email. There is no need to leave the checkout page open your web browser.
FrameThrower PiStorm600 Amiga A600
FrameThrower PiStorm600 Amiga A600 adapter, this enables an output RTG desktop and native Amiga 15khz screen modes using single PiStorm accelerator HDMI output.
GoDrive Pro Amiga A1200 A500 Large OLED Gotek
GoDrive Pro for the Amiga is a Gotek drive for the Amiga A1200 and A500/500 Plus with a large 2.42″ OLED screen.
FURIA Amiga A600 accelerator (Passive Cooler)
Furia Amiga A600 accelerator equipped with CPU Motorola MC68EC020/25 (OC33) MHz and FPU Motorola MC68882/40 MHz, and with onboard 9.5 megs of fast memory.
A630 Rev 3 Accelerator (Bare board)
A630 Rev 3 Accelerator for the Amiga 600 is the latest revision of the A630 modern turbo card. designed for the the classic 68030 Motorola processor (NOT INCLUDED) running at 50Mhz and add an additional FPU (NOT INCLUDED). Perfect for that sweet spot in speed and usefulness for Demos, WHDLoad* gaming, internet and so on. This will give any A600 a great speedboost in a compact unit.
Full specs:
- CPU socket for the Motorola MC68030 clocked on 50MHz CPU (CPU NOT INCLUDED)
- FPU socket for the 68882FN40 (FPU NOT INCLUDED)
- 64MB SDRAM Fast Ram.
- PCMCIA Friendly.
We also sell a fully bullt A630 Rev 3 with CPU and FPU.
Important Information:
MMULib’s for the A630 Accelerator
The A630 Accelerator requires the installation of MMULib’s and it very important you use the right ones for the kickstart ROM you are using:
3.1 Kickstart:
http://main.aminet.net/util/libs/MMULib.lha
http://main.aminet.net/util/libs/MMULib.readme
3.2, 3.2.1 or 3.2.2
Install the MMULib package that came with the installation CD ONLY and NOT the ones from Aminet.
Notes:
- Some demos or games may require disable “CPU CACHE” for better compatibility with the MC68000.
- The card is designed to work with 3.1 Roms and above including 3.2 and 3.2.1 of which can be purchased below.
- The Oscillator will need some insulation tape put on top to stop the A630 touching it.
*2Mb Chip ram is strongly recommended for WHDLoad which is available here
Image for illustration only – no CPU or FPU is included and PCB colour will vary.
Nvidia PC Case Badge White
Nvidia PC Case Badge White, perfect for any PC case, add a touch of nostalgia from a great Nvidia era in PC history. These badges are printed on high quality white vinyl finished with a gel epoxy bubble giving that classic PC badge look and feel.
Nvidia PC Case Badge Green
Nvidia PC Case Badge Green, perfect for any PC case, add a touch of nostalgia from a great Nvidia era in PC history. These badges are printed on high quality white vinyl finished with a gel epoxy bubble giving that classic PC badge look and feel.