Services

SNES Modding Service Region Free 50/60hz
SNES Region Free, Switchless, DeJitter 50/60hz Modding Service
SNES region free, switchless, deJitter DFO modding service. Free your Super Nintendo or Super Famicom from being locked to one region with this modification. Play any region Super Nintendo or Super Famicom PAL or NTSC and play it how it was meant to be played. What does the modification do?
  • Works with all revisions of SNES or Super Famicom games console.
  • SuperCIC: Lockout chip replacement 50Hz/60Hz switch capability.
  • uIGR - Use the controller to perform resets or 60Hz and 50Hz switching.
  • Region Patch: Overrides region protection based on picture processing status reads.
  • DeJitter: Removes jitter on sync for NTSC mode.
  • DFO: Dual Frequency Oscillator, used to switch between base clocks for 50Hz, 60Hz video-modes.
  • Premium ENIG (gold immersion) finish.
  Full Details: SuperCIC By holding down the reset button on the console this will switch between 50Hz (green LED), 60Hz (red LED) or Auto-Region (yellow LED). If you have a SD2SNES you are able to pair the SuperCIC with the flash card. With this you are able to switch between 60Hz and 50Hz mode. However, you need to have the uIGR, which is master for the region setting, in SuperCIC pass through mode. uIGR The uIGR looks at the controller inputs directly and is then able to detect certain button combinations. All button combinations are highlighted below: Region forcing:
  • 60Hz: L + R + Select + A
  • 50Hz: L + R + Select + Y
  • Auto: L + R + Select + B
  • S-CIC pass through: L + R + Select + D-pad left OR L + R + Select + D-pad right
Reset:
  • Simple reset: L + R + Select + Start
  • Double reset (back to main menu of sd2snes): L + R + Select + X
  Region Patch Overwrites region if game request register $213F, where bit 4 represents the region. You also have to consider switching off the region patch if using non-original cartridges or flash cards (sd2snes with Pairmode with SuperCIC is not a problem). DeJitter While in NTSC mode the SNES outputs a shorter scanline in non-visible area. This might be an issue for certain TVs if you use pure analog to digital conversion without frame buffer like the OSSC does. DeJitter ‘removes’ this shorter line by pausing the clock for a few cycles. As drawback this mechanic varies output timing a bit, however the inaccuracy is neglectable when comparing it to clock variations throughout different consoles. At the moment, DeJitter is enabled by default and can only be disabled by setting jumper SJ31. DFO Short for Dual Frequency Oscillator. Actually in combination with the CPLD this allows to switch between three output clocks plus two colour carrier clocks.   The service includes:
  • Testing of the SNES or Super  Famicom beforehand
  • Full strip down of the console
  • Full Installation of the SNES MultiRegion with DeJitter QID modification
  • Testing using PAL and JAP (NTSC) gaming cartridges
  • Final testing and video taken of unit working and switching.
We can also offer a full recapping service and regulator upgrade.    
£79.16 Ex. VAT Read more
xT Accelerator for Amiga 600
xT Accelerator Amiga 600, 28Mhz CPU, 11MB Fastram
xT Accelerator Amiga 600 with an onboard 28Mhz CPU with 11MB Fastram is one of the smallest and slimmest accelerator cards for the Amiga 600 computer, with some extra skill you can also fit the original HDD sled to it.The card is mounted on top of the MC68000 PLCC68 processor. All configuration options are available in the CLI.   Full specs:
  • CPU MC68SEC000AA20, clocked on 28MHz.
  • 11MB Fast Ram.
  • MapROM Feature.
  • PCMCIA Friendly - Ram needs to be set to 4MB.
  • Embedded hardware DriveSWAP DF0/DF1 (Boot Selector).
 
Notes:
  • Some demos or games may require disable "CPU CACHE" for better compatibility with the MC68000.
  • The card is designed to work with 3.1 Roms and above including 3.2 and 3.2.1.
  • PCB Colour will vary
*2Mb Chip ram is strongly recommended for WHDLoad which is available here      
£79.16 Ex. VAT Add to basket
Amiga PSU DUO Amiga A500-600-1200 and CD32
Commodore Amiga PSU for A500/600/1200 & CD32 (DUO Edition)
Commodore Amiga PSU DUO EDITION for 1 x A500/A600/A1200 and 1 x Amiga CD32 up to 8A at 5VDC strong, adjustable PSU for regular and accelerated Commodore Amiga A500, A500+, A600, A1200 and Amiga CD32. The new Amiga PSU DUO Edition is a modern, 50W strong replacement power supply unit for Commodore Amiga computer systems.provides stable, filtered, adjustable 5VDC (up to 8.0A), 12VDC (up to 0.5A) and -12VDC (up to 0.15A) by industrial grade components. Now your Vampire, Blizzard, ACA or TF536 accelerator will get enough juice to work flawlessly with full MHz clocks. Factory trimmed for stock Amiga 500 reference load, may be adjusted to give exact 5VDC with 2-3x heavier loads.
Key features:
  • 1 x A500 A500+ A600 A1200 compatible (rectangular 5pin DIN plug)
  • 1 x CD32/A590 compatible (round 4pin DIN plug)
  • Stabilized, double protected +5VDC up to 8.0A rated output (total, 4A per channel max)
  • Stabilized +12VDC up to 1.2A rated output (0.6A per channel max)
  • Stabilized -12VDC up to 0.15A rated output
  • Trim potentiometer for 5VDC fine adjustments (5-5.5V range) common for both outputs
  • Double over current protection, individual for each output
  • Durable main AC power On/Off switch
  • Set of LED status indicators (green 5VDC, yellow 12VDC, blue -12VDC)
  • Eco friendly design: consumes ~20% less power compared to original PSU set
  • Configurable set of detachable output cables. Versions for regular Amiga 500/600/1200 or CD32/A590 are available (1.6 m length)
  • Detachable input AC cable allowing you to use your own desired cable length (cable included)
  • Weight only 0.3 KG
  • Universal AC input range to support all worldwide power standards (accepts 110-240 VAC)
  • Meets safety standards: UL60950-1, TUV EN60950-1, ANSI/AAMI ES60601-1, TUV EN60601-1, IEC60601-1
  • UK Stock
Checkout Ravi Abbot Review: [kad_youtube url="https://youtu.be/lqZuQ2S5TL4" ]
Warning! Risk of electrical shock and energy hazard when opened. All failures should be examined by a qualified technicians only. Risk of fire or electrical shock. The ventilation holes should be protected from foreign objects or dripping liquids. Please do not install power supplies in places with high ambient temperature or close to the heat source. Enclosed power supplies are intent to work in indoor locations, it's not allowed to use power supplies outdoor, in dust or high moisture. Output current and output wattage must not exceed the rated values. This replacement Amiga PSU has been designed for Commodore Amiga 1200 vintage computer systems only and should be considered as an integral component of Amiga computer system. Do not connect to any other devices as it's not a general purpose PSU. Manufacturer is not responsible for any consequences of unauthorised or arbitrary repairs, modifications or incorrect usage. Please notice that new, properly working replacement Amiga PSU is reducing the system's potential fail rate but still is not guaranteeing that entire Amiga system will work correctly (it's >30 years old).  
£79.16 Ex. VAT Add to basket
Pistorm32-Lite CM4 Adaptor and Expansion board with HDMI, USB & Ethernet
PiStorm32-Lite CM4 Adaptor with Expansion Breakout
PiStorm32-Lite CM4 adaptor with expansion breakout with HDMI, Ethernet, USB. This is designed to be attached to the PiStorm32-lite adaptor to allow you add an Raspberry PI CM4 module. What's included:
  • CM4 Adapter (Allows connection of Expansion Breakout and Compute Module 4)
  • Passive Cooler
  • Expansion Breakout that provides HDMI, USB and Ethernet Ports
  • Flex wire 40Pin 20cm
  • Printed IO cover (3D printed)
  We also just sell the Pistorm32-Lite kits with Raspberry Pi 3A+ here
  NOTE: The PiStorm32-Lite CM4 product is an open source project and will require some knowledge of the  Amiga  
£74.99 Ex. VAT Read more
Apple Mac Classic II Analogue Board Recapping
Macintosh Classic II Analogue Board Recapping
Macintosh Classic II analogue board recapping service, all board revisions, all electrolytic capacitors are replaced using high quality capacitors.
  • Removal of existing capacitors.
  • Clean-up and preparation of area.
  We also offer a Apple Mac Classic II Logic Board recapping service.
NOTE this is NOT a repair service, the Apple Mac Classic II needs to be in working order - All we need is the analogue board to be sent.    
£74.99 Ex. VAT Add to basket
FM Towns Marty
FM Towns Marty Recapping Service
FM Towns Marty Recapping Service is where we replace all the electrolytic capacitors on the mainboard, PSU (both Tamura and Eastern PSU's are covered) and CD Drive. We would need the entire console and controller to be sent. We can also offer just the mainboard, PSU or CD Drive if needed, please by all means contact us. What's included:
  • Testing Video, Audio and CD Drive.
  • Full strip down of the unit.
  • Removal of all electrolytic capacitors on the Mainboard, PSU and CD Drive - Approx 53 capacitors.
  • Cleanup any capacitor leakage.
  • Replace with tier one brands of capacitors.
  • Test video, audio and CD Drive.
  • Reassemble and retest.
  We are able to recap both models.   Note: This is not a repair service  
£74.99 Ex. VAT Read more
Atari STe Recapping Service
Atari 520 STe / 1040 STe / 4160 STe Recapping Service inc PSU
Atari 520 STe / 1040 STe / 4160 STe recapping service including recapping of STe PSU, all board revisions. This service includes both recapping of the Atari STe motherboard and PSU.
  • Check of the STe motherboard and PSU before recapping is begun.
  • Removal of existing capacitors.
  • Clean-up and preparation of area.
  • Replace using Panasonic/Wurth/KEMET capacitors.
  • Retest (Video, Audio, Floppy Boot) using diagnostic cartridge.
We also provide a recapping service for the  Atari STF / STFM   What do you need to send? All we need is the mainboard and PSU, so please only send the board and PSU in its metal shielding. If however you choose to send the whole unit, there is an option to do that also via the choices below.  
£74.99 Ex. VAT Select options
Amiga A600 PiggyBackNot V3 RGB2HDMI
Amiga A600 PiggyBackNot RGB2HDMI 1Mb Expansion
Amiga A600 PiggyBackNot V3 is an Amiga 600 trapdoor expansion that adds 1Mb Chip Ram and also integrates a RGB2HDMI circuit that then allows you to add a Raspberry Pi Zero (not included). The benefit of this upgrade is that it allows you to add a selection of upgrades that plug over the 68000 CPU, for example the 8Mb Mini Fast Ram card the xT 28Mhz, 11Mb Accelerator or the awesome A630 68030, 64Mb accelerator. So you can have HDMI output and the extra fast ram or accelerator in a very tidy package. Specifications:
  • 1MB additional CHIP RAM
  • Implemented RGB2HDMI logics in small CPLD
  • RPI Zero connector
  • Integrated denise adapter on flex ffc cable.
  • RTC Socket (Add a Real Time Clock Chip
  • 3 x Clockports
  • Flexible mHDMI to HDMI FFC cable included!
  Benefits:
  • Slim construction, No need to remove the trapdoor cover or replace with one that allows the expansion
  • Module does not interfere with fast ram cards or accelerator cards.
Not included:
  • Raspberry Pi
  • SD Card
  • 3D Printed HDMI Mount
    1 Year RTB Warranty.   A600 PiggyBackNot PCB Colour will vary, Raspberry Pi Zero NOT included.   RGB2HDMI software can be downloaded from here    
£70.83 Ex. VAT Read more
PiStorm32-Lite for Amiga A1200
PiStorm32 Lite for Amiga A1200 Adaptor Only
PiStorm32 Lite Adaptor for the Amiga A1200 is designed to connect one of the Raspberry Pi's listed below (not included) NOTE: We do sell a plug and play package here which includes PiStorm32-Lite, Raspberry Pi 3A & SD Card. Once you add your own Raspberry Pi, setup an SD card and plug it in the trapdoor of the A1200 like all A1200 accelerators (TF1230 or TF1260) you will have an accelerated Amiga 1200!   Compatible Rasperry Pi's:
  • Raspberry Pi 3A
  • Raspbery Pi 3B
  • Raspberry Pi 4B
  Want to know more about the PiStorm check out the following link: https://github.com/PiStorm/pistorm32-lite-hardware   Compatible Rasperry Pi's:
  • Raspberry Pi 3A
  • Raspbery Pi 3B
  • Raspberry Pi 4B
  With the Pistorm32-lite the A1200 can go up to a 68040 and using a Pi4 you could see 2000 Plus Mips! Want to know more about the PiStorm check out the following link: https://github.com/PiStorm/pistorm32-lite-hardware   The PiStorm adaptors are professionally manufactured. and a contribution to the developer is made to support this project.      
£70.83 Ex. VAT Read more
Amiga A4000 Reproduction Box
Amiga A4000 Reproduction Box
Amiga A4000 reproduction box - These are brand new and designed to be used as box art or to house your Amiga 4000 including keyboard and accessories. These are true reproductions of the original boxes created by plakativ-druck.ch used when the A4000 was shipped.
Key features:
  • Box is true to the original size and design.
  • Including "Innards" for positioning the Amiga A4000 computer and accessories.
  • Laminated outside / moisture repellent.
  • Will be delivered flat in a large envelope.
We also offer Amiga Reproduction boxes for the following: Commodore Amiga A1200 Commodore Amiga A600 Commodore Amiga A500 Commodore Amiga A500 Plus Commodore Amiga CD32   Please note: This is an Amiga A4000 reproduction box and NOT AN ORIGINAL.
£70.83 Ex. VAT Add to basket
Amiga PSU Boost A500 - A500 Plus
Commodore Amiga PSU for A1200 (BOOST VERSION)
Commodore Amiga PSU for A1200 BOOST VERSION, up to 8A at 5VDC strong, adjustable PSU for regular and accelerated Commodore Amiga A500, A500+, A600, A1200. The new Amiga PSU BOOST is a modern, 50W strong replacement power supply unit for Commodore Amiga computer systems. Based on our famous Amiga DUO/DUO+ PSU experiences provides stable, filtered, adjustable 5VDC (up to 8.0A), 12VDC (up to 0.5A) and -12VDC (up to 0.15A) by industrial grade components. Now your Vampire, Blizzard, ACA or Furia accelerator will get enough juice to work flawlessly with full MHz clocks. Factory trimmed for stock Amiga 500 reference load, may be adjusted to give exact 5VDC with 2-3x heavier loads.
Key features:
  • Commodore Amiga 500, 500+, 600, 1200 compatible
  • Stabilized & filtered 5VDC up to 8A output (peak)
  • Stabilized & filtered 12VDC up to 0.5A output
  • Stabilized & filtered -12VDC up to 0.15A output
  • 5VDC manual adjustment feature (potentiometer)
  • Factory calibrated for stock Amiga 500 reference load
  • Active & passive over voltage protections for main +5VDC line
  • Over current protection for all output lines
  • Integrates Protection & Adjustment LED Module add-on
  • Fully isolated & fused on AC side
  • Durable power On/Off switch (black)
  • Status LED (Good Status Green)
  • Long output cable (1.8m) with rectangular DIN 5-pin plug
  • Detachable input AC cable for all versions (cable included)
  • Weight only 0.4 KG (2x less than original PSU)
  • UK Stock
 
Warning! Risk of electrical shock and energy hazard when opened. All failures should be examined by a qualified technicians only. Risk of fire or electrical shock. The ventilation holes should be protected from foreign objects or dripping liquids. Please do not install power supplies in places with high ambient temperature or close to the heat source. Enclosed power supplies are intent to work in indoor locations, it's not allowed to use power supplies outdoor, in dust or high moisture. Output current and output wattage must not exceed the rated values. This replacement Amiga PSU has been designed for Commodore Amiga 1200 vintage computer systems only and should be considered as an integral component of Amiga computer system. Do not connect to any other devices as it's not a general purpose PSU. Manufacturer is not responsible for any consequences of unauthorised or arbitrary repairs, modifications or incorrect usage. Please notice that new, properly working replacement Amiga PSU is reducing the system's potential fail rate but still is not guaranteeing that entire Amiga system will work correctly (it's >30 years old).  
£70.83 Ex. VAT Read more
Amiga 1200 Reproduction box - Brand New
Amiga 1200 Reproduction Box Brand New
THIS WILL BE THE VERY LAST PRODUCTION SO THESE ARE A SPECIAL ORDER   Amiga 1200 reproduction box, these are brand new and designed to be used as box art or to house your Amiga A1200. These are true reproductions of the original boxes created by plakativ-druck.ch used when the Amiga 1200 was shipped.
Key features:
  • Box is true to the original size and design.
  • Including "Innards" for positioning the Amiga A1200 computer and accessories.
  • Laminated outside / moisture repellent.
  • Will be delivered flat in a large envelope.
We also offer Amiga Reproduction boxes for the following: Commodore Amiga A1200 Commodore Amiga A600 Commodore Amiga A500 Commodore Amiga A500 Plus Commodore Amiga CD32   Please note: This is an Amiga 1200 reproduction box and NOT AN ORIGINAL.
£70.83 Ex. VAT Read more