Atari ST PSU for Atari 520ST & 260ST
Atari ST PSU is a 50W strong, modern replacement power supply unit for Atari 520ST and 260ST computer systems using external power supply. PSU provides stable filtered 5VDC up to 4.0A, 12VDC up to 2.0A and -12VDC up to 0.5A. All by industrial grade AC/DC power supply. Carefully trimmed to offer best performance. The best and most affordable basic Atari ST external PSU replacement on the market. Can be upgraded to adjustable version offering 5VDC voltage fine tuning to set exact 5VDC for your particular system. The one and only absolute industry standard using the Mean-Well’s RPT-60B as a base component.
Key features:
- ATARI 520ST, 520ST+, 260ST, 260ST+ compatible
- Stabilized & filtered 5VDC up to 4A output (4.4A peak)
- Stabilized & filtered 12VDC up to 2A output (2.2A peak)
- Stabilized & filtered -12VDC up to 0.5A output (0.55A peak)
- Active & passive over voltage protection for main +5VDC line
- Over current protection for all output lines
- Fully isolated & fused on AC side
- Power On/Off switch
- Long output cable (1.8m) with round DIN 7-pin female plug
- Detachable input AC cable for all versions
- Weight only 0.4 KG (2x less than original Atari ST PSU)
- Runs COLD!
- Safety standards: UL60950-1, TUV EN60950-1, ANSI/AAMI ES60601-1, TUV EN60601-1, IEC60601-1
- UK Stock
Warning!
Risk of electrical shock and energy hazard when opened. All failures should be examined by a qualified technicians only. Risk of fire or electrical shock. The ventilation holes should be protected from foreign objects or dripping liquids. Please do not install power supplies in places with high ambient temperature or close to the heat source. Enclosed power supplies are intent to work in indoor locations, it’s not allowed to use power supplies outdoor, in dust or high moisture. Output current and output wattage must not exceed the rated values.
ZX Spectrum PSU for +2A, +2B, +3 NEW
ZX Spectrum PSU for +2A, +2B, +3 is a modern, 50W strong, replacement power supply unit.
Atari Mega STe PSU Recapping Service
Atari Mega STe 1000 PSU recapping service – NOTE this is NOT a repair service.
- Removal of existing capacitors.
- Cleanup and preparation of area.
- Replace using quality capacitors.
- Test output voltages (not under load)
Recapping the Atari STe PSU is a good preventive measure, the reason being these capacitors are under alot of stress (which they are designed to take of course) however with age they start getting tired which could lead to issues later on.
All that needs to be sent is the Atari Mega STe PSU itself.
PiStorm600 Adaptor for Amiga A600
PiStorm600 for the Amiga A600 is an adaptor in which you plug in either a Raspberry Pi Model 3A+ or *Raspberry Pi Zero Model 2 (both not included) this provides a budget CPU accelerator for the Amiga 600. Also included is a file-based SCSI device, RTG graphics and several other optional enhancements.
Only the Pi 3-series is compatible with the current firmware version and only the Pi Model 3A+ and Raspberry Pi Zero Model 2 will physically fit in the A600 without modification and you can optionally support the PiStorm600 using M2.5 standoffs to help physically support it which are available as an option below.
Key Features
- Emulate 68010,68020,68030,68040,68060 Processors with or without FPU
- 128Mb Fastram.
- File-based SCSI device.
- RTG graphics from the Pi itself.
Notes:
Powering the A600/PiStorm
It is possible if you have a weak PSU or the Amiga 600 has not been recapped you may see instability issues as with any accelerator, you have a few options all of which are available below, If your using a Pi Zero2 then it is unlikely you will need to apply additional power. A Pi 3A+ can consume more power, but this is not often an issue until you start connecting USB devices, you have a few options below:
- You can add extra power via a floppy power connector splitter (available below) which is a new cable which splits the floppy power to power both your internal floppy drive and the PiStorm via its built in Molex connector (DO NOT ADD POWER OTHER THAN FROM THE AMIGA ITSELF OR TRY AND USE IT TO POWER OTHER DEVICES).
- Make sure your Amiga has been recapped, we offer 2 options Standard and Premium.
- Purchase a new Amiga PSU of which we also offer 2 versions, A600 Standard PSU or A600 Boost PSU which also as a 5VDC line adjustment to give a perfect 5 Volts to the Amiga 600.
We always suggest recapping in the first instance as tired caps can cause other issues like poor sound or prevent the Amiga booting up.
NOTE: PiStorm600 is a community project and will require some knowledge of the Amiga. Hardware which comes with a 1 year RTB warranty. hints and tips are available via the following Discord channel https://discord.com/invite/j6rPtzxaNW Also this product is still in BETA and while compatibility is very high, updates are always being released to increase compatibility with software and games.
We support developers by donating a percentage of sales, the PiStorm A600 adaptors are professionally manufactured and are RoHS compliant. This project was designed by Lemaru
*Using the Raspberry Pi Zero Model 2 is possible as mentioned but you do lose a little in performance.
PiStorm Adaptor Amiga A500 – A500 Plus
PiStorm Adaptor is designed to connect to the Raspberry Pi 3A + (not included but available as an option below). Placed in the DIP64 (CPU) socket of your Amiga A500, A500 Plus or A2000 in conjunction with the Raspberry Pi, it can emulate the operation of the 68020/68030/68040 processor. The software running on PiOS greatly extends the functionality of the Amiga – adding FAST memory, RTG (graphics card) and a network card. PiStorm is designed for Amiga computers (A500 / A500 Plus / A1500 / A2000), but should work with any 16-bit computer equipped with a 68000 CPU socket (FC adapter lines are not currently used / supported by firmware and cannot be guaranteed to work properly on systems with use them). Overall performance with the current use of “Musashi” as a 68k processor emulator is around 70-80 MHz 68030.
This adapter requires:
- Raspberry Pi model 3A
- 32Gb SD Card configured to boot in to WB
All available as an option below
Want to know more about the PiStorm check out the following link: https://github.com/captain-amygdala/pistorm
NOTE: This is a community project and will require some knowledge Amiga. We DO NOT provide any support for getting this product running, but support is available via the following Discord channel https://discord.com/invite/j6rPtzxaNW Also this product is still in BETA and while compatibility is very high, updates are always being released to increase compatibility with software and games.
We do sell refurbished Amiga A500 and A500 Plus’s which can have a PiStorm installed tested and running. Also we can add a PiStorm installation as part of any Amiga A500 or A500 Plus Service.
We support developers and a percentage of the purchase price of the PiStorm adaptor is given to Claude Schwarz
The PiStorm adaptors are professionally manufacture and are RoHS compliant.
Amiga A4000 Recapping Service (Standard)
Amiga A4000 recapping service, all board revisions, NOTE this is NOT a repair service.
- Check of the board before recapping is begun.
- Removal of existing capacitors.
- Clean-up and preparation of area.
- Replace using Panasonic/Wurth/KEMET capacitors.
- Retest (Video, Audio, Floppy Boot, SCSI (if HDD is present).
Overseas recapping orders
Overseas orders are very welcome and we are able to provide you return shipping costs at the checkout.
To do this add any of our recapping services to your shopping basket and then at the checkout simply fill in the billing and shipping form including your telephone and email address (important) and click the ‘Request a quote‘ link.
You will receive an email within 24hrs with the shipping cost and you can then proceed with the order by clicking on the ‘Complete your order‘ within the email. There is no need to leave the checkout page open your web browser.
Amiga CD32 Recapping Service (Standard)
Amiga CD32 recapping service, all board revisions (Rev 3 & 4). NOTE this is NOT a repair service.
- Check of the board before recapping is begun.
- Removal of existing capacitors (both SMD and radial capacitors).
- Clean-up and preparation of area.
- Replace using Panasonic/Wurth/KEMET capacitors. NOTE: Rev 3 board capacitors C408 and C411 installed correctly.
- Retest (Video, Audio).
Macintosh Classic II Recapping Service (Premium)
Macintosh Classic II recapping service (Premium), all board revisions, all electrolytic capacitors are replaced. The Macintosh Classic logic board is recapped using high quality capacitors. NOTE this is NOT a repair service, the Macintosh Colour Classic needs to be in working order.
- Removal of existing capacitors.
- Clean-up and preparation of area.
- Replace all surface mount capacitors using polymer (non leaking) capacitors.
ACA500Plus Case Amiga A500 A500 Plus
ACA500Plus case (transparent), the perfect enclosure for the ACA500Plus with all parts are laser cut.
What’s included:
- 7 acrylic parts, transparent
- 6 adhesive feet,
- 8 threaded bolts,
- 13 screws,
- 1x nut,
- 3 acrylic discs (washers).
- Assembly instructions (around 15/20 mins)
There is a small assembly video on YouTube here .
Note on ventilation:
The case has ventilation slots on both the top and bottom for passive cooling.
Depending on the hardware installed, the temperature development in the housing and the installed components must be taken into account!
FrameThrower PiStorm600 Amiga A600
FrameThrower PiStorm600 Amiga A600 adapter, this enables an output RTG desktop and native Amiga 15khz screen modes using single PiStorm accelerator HDMI output.
Amiga A600 A604n 1Mb Chip Ram Expansion Card
Amiga A600 A604n 1Mb chip ram expansion card provides 1Mb chip ram upgrade for a total of 2Mb chip ram.
Macintosh Performa 450 Apple Recapping Service (Premium)
Macintosh Performa 450 Recapping Service (Premium), all board revisions, all electrolytic capacitors are replaced. The Macintosh Colour Classic logic board is recapped using high quality capacitors. NOTE this is NOT a repair service, the Macintosh Performa needs to be in working order.
- Removal of existing capacitors.
- Clean-up and preparation of area.
- Replace all surface mount capacitors using polymer (non leaking) capacitors.