Services
Showing 25–36 of 252 results
Amiga CD32 Recapping Service (Standard)
Amiga CD32 recapping service, all board revisions (Rev 3 & 4). NOTE this is NOT a repair service.
- Check of the board before recapping is begun.
- Removal of existing capacitors (both SMD and radial capacitors).
- Clean-up and preparation of area.
- Replace using Panasonic/Wurth/KEMET capacitors. NOTE: Rev 3 board capacitors C408 and C411 installed correctly.
- Retest (Video, Audio).
Commodore C64 PSU (NEW) Breadbin and C64C
Commodore C64 PSU for the C64 Breadbin and C64C, these are brand new and modern with It's 20 watt of total combined output power and 2x smaller in dimensions & weight.
NOTE: LAST UNITS HAS US PLUG
Warning! Risk of electrical shock and energy hazard when opened. All failures should be examined by a qualified technicians only. Risk of fire or electrical shock. The ventilation holes should be protected from foreign objects or dripping liquids. Please do not install power supplies in places with high ambient temperature or close to the heat source. Enclosed power supplies are intent to work in indoor locations, it's not allowed to use power supplies outdoor, in dust or high moisture. Output current and output wattage must not exceed the rated values. This replacement Commodore C64 PSU has been designed for Commodore C64 "breadbox", C64C, C64D & VIC20 vintage computer systems only and should be considered as an integral component of Amiga computer system. Do not connect to any other devices as it's not a general purpose PSU. Manufacturer is not responsible for any consequences of unauthorised or arbitrary repairs, modifications or incorrect usage. Please notice that new, properly working replacement Amiga PSU is reducing the system's potential fail rate but still is not guaranteeing that entire Amiga system will work correctly (it's >30 years old).
Key features:
- Commodore C64 "breadbox", C64C, C64D & VIC20 compatible
- Stabilized & filtered 5VDC now upgraded to 4.0A output (20W)!
- 9VAC up to 1.11A (10VA) output by real heavy duty trafo (new model, now voltage matches the original!)
- Carefully calibrated for C64 reference load (fixed version)
- 5VDC voltage fine tuning feature available with Adjust & Protect Module option.
- Multiple active & passive over current and over voltage protections
- Fully isolated, fused on AC and DC side
- Power On/Off switch
- Status LED
- Long output cable (1.8m) with round DIN 7-pin plug
- Detachable input AC cable for UK and EU (cable included)
- Fixed input AC cable for USA and AU versions
- Weight only 0.6 KG (2x less than original)
- Runs COLD!
- UK Stock
Warning! Risk of electrical shock and energy hazard when opened. All failures should be examined by a qualified technicians only. Risk of fire or electrical shock. The ventilation holes should be protected from foreign objects or dripping liquids. Please do not install power supplies in places with high ambient temperature or close to the heat source. Enclosed power supplies are intent to work in indoor locations, it's not allowed to use power supplies outdoor, in dust or high moisture. Output current and output wattage must not exceed the rated values. This replacement Commodore C64 PSU has been designed for Commodore C64 "breadbox", C64C, C64D & VIC20 vintage computer systems only and should be considered as an integral component of Amiga computer system. Do not connect to any other devices as it's not a general purpose PSU. Manufacturer is not responsible for any consequences of unauthorised or arbitrary repairs, modifications or incorrect usage. Please notice that new, properly working replacement Amiga PSU is reducing the system's potential fail rate but still is not guaranteeing that entire Amiga system will work correctly (it's >30 years old).
Amiga 1200 Gotek Drive, Printed Mount, OLED Display and FlashFloppy
Amiga 1200 Gotek drive is a great replacement for your failing Amiga 1200 floppy drive or you wish to simply replace it with a Gotek drive. These are plug and play and come pre flashed with FlashFloppy in that you simply remove your existing floppy drive and replace it with this unit (you use your existing bracket). 3 new screws will also be supplied to secure the Gotek drive to your Amiga.
You will need a USB memory stick (NOT included) with your loaded ADF files but we offer an option for a pre-configured USB stick below.
What are gotek drives in detail? Read here What is FlashFloppy check out this link Want to know even more about them, checkout retro32.com's review of them here Also checkout one of our favorite youtube streamers TheGebs24 and her views on the Gotek drive!
What are ADF files?
ADF files is the standard Amiga Disk Format for floppy disk images. no different to Sega or Nintendo roms, ADF's are images of Amiga floppy disk games. Not only could you have access to a huge back catalogue of retro Amiga games, but there are still brand new games being released today, for example: Raid over Moscow or Bridge Strike these are all available as ADF files. But you not limited to games or programs, but you have access to tons of Amiga demos (if your into that scene).What are gotek drives in detail? Read here What is FlashFloppy check out this link Want to know even more about them, checkout retro32.com's review of them here Also checkout one of our favorite youtube streamers TheGebs24 and her views on the Gotek drive!
Amiga A1200 Memory Expansion 11Mb
Amiga A1200 11Mb memory expansion card upgrades your Amiga A1200 with 11Mb of additional ram which is perfect for WHDLoad or just want a little boost! The Ex1T card is installed on the expansion port accessible through the trapdoor located under the Amiga 1200. Once in place your Amiga will be 2/3 times faster than the original base model, thanks to the modern memory being used.
The card can also be configured by a jumper or software with the following configurations:
- 5.5MB will be always available,
- Additional 4MB which can be activated / deactivated via switch or software (Not PCMCIA compatible),
- Additional 1.5MB software activated (Compatible with Amiga OS 3.0, 3.1 and 3.2 but not compatible with Amiga OS 3.1.4 due to a bug)
Amiga A600 PiggyBackNot RGB2HDMI 1Mb Expansion
Amiga A600 PiggyBackNot V3 is an Amiga 600 trapdoor expansion that adds 1Mb Chip Ram and also integrates a RGB2HDMI circuit that then allows you to add a Raspberry Pi Zero (not included). The benefit of this upgrade is that it allows you to add a selection of upgrades that plug over the 68000 CPU, for example the 8Mb Mini Fast Ram card the xT 28Mhz, 11Mb Accelerator or the awesome A630 68030, 64Mb accelerator. So you can have HDMI output and the extra fast ram or accelerator in a very tidy package.
Specifications:
- 1MB additional CHIP RAM
- Implemented RGB2HDMI logics in small CPLD
- RPI Zero connector
- Integrated denise adapter on flex ffc cable.
- RTC Socket (Add a Real Time Clock Chip
- 3 x Clockports
- Flexible mHDMI to HDMI FFC cable included!
- Slim construction, No need to remove the trapdoor cover or replace with one that allows the expansion
- Module does not interfere with fast ram cards or accelerator cards.
- Raspberry Pi
- SD Card
- 3D Printed HDMI Mount
External Gotek Drive – All Commodore Amiga Computers
External Gotek drive (new version) with a 0.96" OLED display (5% bigger than the original OLED), rotary control housed in a brand new full metal enclosure made with strong 2mm thick aluminium metal available in 2 colours, Anodised black or Satin cream coating, with plenty of space inside for extra modifications and components.
Fully compatible with the entire Commodore Amiga family of computers including:
- Amiga A500 & Amiga A500 Plus
- Amiga A600
- Amiga A1200
- Amiga A1000
- Amiga A1500
- Amiga A2000
- Amiga A3000
- Amiga A4000
- Amiga 4000T
- External Gotek full metal case (choice of Anodised black or Satin cream).
- Internal Gotek Drive with 0.96" OLED Display and rotary control.
- Flashed with latest version of FlashFloppy.
- External ribbon from Gotek drive to Amiga External Floppy port (also provides power).
Amiga ATX PSU Adaptor – A1000, A2000, A3000
PRODUCT DISCONTINUED
Amiga ATX PSU Adaptor which can be used in an ATX tower case or inside an A1000, A1500, A2000, A3000 (Big Box) Amiga, this adapter provides the -5V and ‘Tick’ signal. For the A3000, the FAIL signal is available to use.
This is the highest rated power adapter available, it can safely handle the following power levels:
+5V @ 15A
+12V @ 8A
This yields a system power of 175W.
One DIP switch sets the power switch type, momentary (as used on ATX cases) or latching (as used on original power cases. The other DIP switch sets the ‘Tick’ frequency.
PCB dimensions, 68x41mm
Does not include any ATX PSU.
Designed and built by Ian Stedman
PiStorm Adaptor Amiga A500 – A500 Plus
PiStorm Adaptor is designed to connect to the Raspberry Pi 3A + (not included but available as an option below). Placed in the DIP64 (CPU) socket of your Amiga A500, A500 Plus or A2000 in conjunction with the Raspberry Pi, it can emulate the operation of the 68020/68030/68040 processor. The software running on PiOS greatly extends the functionality of the Amiga - adding FAST memory, RTG (graphics card) and a network card. PiStorm is designed for Amiga computers (A500 / A500 Plus / A1500 / A2000), but should work with any 16-bit computer equipped with a 68000 CPU socket (FC adapter lines are not currently used / supported by firmware and cannot be guaranteed to work properly on systems with use them). Overall performance with the current use of "Musashi" as a 68k processor emulator is around 70-80 MHz 68030.
This adapter requires:
NOTE: This is a community project and will require some knowledge Amiga. We DO NOT provide any support for getting this product running, but support is available via the following Discord channel https://discord.com/invite/j6rPtzxaNW Also this product is still in BETA and while compatibility is very high, updates are always being released to increase compatibility with software and games. We do sell refurbished Amiga A500 and A500 Plus's which can have a PiStorm installed tested and running. Also we can add a PiStorm installation as part of any Amiga A500 or A500 Plus Service. We support developers and a percentage of the purchase price of the PiStorm adaptor is given to Claude Schwarz The PiStorm adaptors are professionally manufacture and are RoHS compliant.
- Raspberry Pi model 3A
- 32Gb SD Card configured to boot in to WB
NOTE: This is a community project and will require some knowledge Amiga. We DO NOT provide any support for getting this product running, but support is available via the following Discord channel https://discord.com/invite/j6rPtzxaNW Also this product is still in BETA and while compatibility is very high, updates are always being released to increase compatibility with software and games. We do sell refurbished Amiga A500 and A500 Plus's which can have a PiStorm installed tested and running. Also we can add a PiStorm installation as part of any Amiga A500 or A500 Plus Service. We support developers and a percentage of the purchase price of the PiStorm adaptor is given to Claude Schwarz The PiStorm adaptors are professionally manufacture and are RoHS compliant.
Commodore Amiga PSU for A500 A500 Plus
Commodore Amiga PSU for A500 or A500 Plus, these are brand new and modern with It's 50W (55W peak) of total combined output power making it nearly 2x times stronger than original Commodore Amiga PSU and 2x smaller in dimensions & weight.
Warning! Risk of electrical shock and energy hazard when opened. All failures should be examined by a qualified technicians only. Risk of fire or electrical shock. The ventilation holes should be protected from foreign objects or dripping liquids. Please do not install power supplies in places with high ambient temperature or close to the heat source. Enclosed power supplies are intent to work in indoor locations, it's not allowed to use power supplies outdoor, in dust or high moisture. Output current and output wattage must not exceed the rated values. This replacement Amiga PSU has been designed for Commodore Amiga 500, 500+ vintage computer systems only and should be considered as an integral component of Amiga computer system. Do not connect to any other devices as it's not a general purpose PSU. Manufacturer is not responsible for any consequences of unauthorised or arbitrary repairs, modifications or incorrect usage. Please notice that new, properly working replacement Amiga PSU is reducing the system's potential fail rate but still is not guaranteeing that entire Amiga system will work correctly (it's >30 years old).
Key features:
- Stabilized & filtered 5VDC up to 4A output (4.4A peak)
- Stabilized & filtered 12VDC up to 2A output (2.2A peak)
- Stabilized & filtered -12VDC up to 0.5A output (0.55A peak)
- Carefully calibrated for Amiga 500 reference load
- Active & passive over voltage protection for main +5VDC line
- Over current protection for all output lines
- Fully isolated & fused on AC side
- Power On/Off switch
- Long output cable (1.8m) with rectangular DIN 5-pin plug.
- Detachable input AC cable for all versions (cable included)
- Weight only 0.4 KG (2x less than original PSU)
- Runs COLD!
- Safety standards: UL60950-1, TUV EN60950-1, ANSI/AAMI ES60601-1, TUV EN60601-1, IEC60601-1
- Manufactured by Electroware
- UK Stock
Warning! Risk of electrical shock and energy hazard when opened. All failures should be examined by a qualified technicians only. Risk of fire or electrical shock. The ventilation holes should be protected from foreign objects or dripping liquids. Please do not install power supplies in places with high ambient temperature or close to the heat source. Enclosed power supplies are intent to work in indoor locations, it's not allowed to use power supplies outdoor, in dust or high moisture. Output current and output wattage must not exceed the rated values. This replacement Amiga PSU has been designed for Commodore Amiga 500, 500+ vintage computer systems only and should be considered as an integral component of Amiga computer system. Do not connect to any other devices as it's not a general purpose PSU. Manufacturer is not responsible for any consequences of unauthorised or arbitrary repairs, modifications or incorrect usage. Please notice that new, properly working replacement Amiga PSU is reducing the system's potential fail rate but still is not guaranteeing that entire Amiga system will work correctly (it's >30 years old).
Amiga A1200 Keyboard Membrane (New)
Amiga A1200 Keyboard Membrane brand new. If you have issues with your Amiga A1200 keyboard with missing keys or missing rows of keys the chances are the membrane needs replacing. These Amiga A1200 brand new (manufactured 2020) membranes are based on the original Mitsumi keyboard membrane (also marked A1200-A) and original Mitsumi Model number 56C774A.
What if you have missing keys or rows of keys on the Keyboard? Try these possible fixes first:
- Check the ribbon is inserted all the way in the connector on the Amiga A1200 mainboard.
- If it's only 1 or two keys the plunger may need a clean, strip down the keyboard and clean the plunger with some IPA.
- If it's a whole row of keys missing its a very strong possibility that the membrane on your needs replacing.
- The final step is to trim off 1mm of the connector (the ribbon end that plugs into the A1200 mainboard).
Gotek Drive pre-flashed with FlashFloppy (Generic)
Gotek drive is a inexpensive solution to replace your Commodore Amiga floppy drive (plus many other makes of computers). These are generic units that simply replace your existing floppy drive or put in an external enclosure. The Gotek drive is pre flashed with FlashFloppy which allows it not only to work with the Commodore Amiga, but also Amstrad CPC computers*, Sinclair Spectrum*, Atari and DOS / IBM PC's*
You will need a USB memory stick (NOT included) with your loaded ADF files.
This Gotek drive will work with all Commodore Amiga computers including:
- Amiga A500
- Amiga A500 Plus
- Amiga A600
- Amiga A1200
- Amiga A1000
- Amiga A1500
- Amiga A2000
- Amiga A3000
- Amiga A4000
- Amiga 4000T
- OLED Display instead of the 3 Digit Display
- Internal Gotek Speaker to hear those floppy sounds!
- Gotek Rotary knob for easily selecting that game, app or demo
Amiga A500 Recapping Service
Amiga A500 recapping service, all board revisions, NOTE this is NOT a repair service.
- Check of the board before recapping is begun.
- Removal of existing capacitors.
- Clean-up and preparation of area.
- Replace using Panasonic/Wurth/KEMET capacitors.
- Retest (Video, Audio, Floppy Boot.