Services

Amiga Capacitor Kit A1200 A600 CD32
Amiga A600 Capacitor Kit Polymer (Premium)
Amiga A600 Capacitor Kit Polymer (Premium). Polymer capacitors compared to the 'standard' liquid electrolyte capacitors, organic polymer is a solid electrolyte, so these capacitors will never leak. These types are still within the Commodore specification compared to other type of capacitors that are used like tantalum or polymer tantalums which should be avoided. We only use quality capacitors and use these in our own Amiga A600 premium recapping service.
  • Complete set of capacitors for Amiga 600 mainboard
  • Compatible with both PAL and NTSC models
  • Compatible with 1.1,1.3, 1.5 and 2B revisions

Package includes:

  • Full set of SMD and through hole capacitors.
  It is assumed the right tools and techniques are used in replacing capacitors as we cannot accept any responsibility for any damage to your board using our Amiga A600 Capacitor Kit. If your an sure we offer a range of Amiga recapping services including fixs and ultrasonic cleaning, contact us for any further information or search Amiga recapping services   Image for illustration only    
£16.66 Ex. VAT Add to basket
TF1260 TerribleFire A1200 Accelerator
TF1260 TerribleFire A1200 Accelerator – NO CPU
TF1260 TerribleFire Amiga 1200 Accelerator which hosts 64Mb Fast Ram, IDE connector (DOES NOT INCLUDE 68060 PROCESSOR). The TF1260 is one of the best 060 accelerators you can purchase for the Amiga 1200 And is the next step up after the TF1230 A1200 Accelerator add-on we sell for those that want that large speed jump. Full specs:
  • 128MByte of fast-ram.
  • IDE Interface - Driver required - ehide.device
  • Compatible with any A1200 motherboard revision.
  • Fits in your old/new stock A1200 case!!!
  • Just add your choice of 68060 processor!
  Processor support: The TF1260 TerribleFire supports all genuine 68060 processors including:
  • MC68060RC50 or XC68060RC50 (Complete with MMU & FPU)
  • MC68LC060RC50 or XC68LC060RC50 (MMU No FPU)
  • MC68EC060RC50 or XC68EC060RC50 (No MMU or FPU)
Only purchase this card if you know you have a genuine 68060 processor, The low end versions that have no MMU or FPU are more often genuine.   Prerequisites 
  • Timing fix is strongly recommended on your A1200 motherboard. We can do this free of charge if you send your board to us (return shipping does need to be covered).
  • Kickstart ROM 3.1, 3.1.4, 3.2, 3.x or 3.9 (not compatible with 3.0).
  What is Terriblefire? Well it's not what it's who, and that person is Stephen Leary who has designed a whole host of accelerators and ram cards for the Amiga A500, A1200 and Amiga CD32. These include many but the most common ones are:   NOTES:
  • For every TF1260 sold we donate a percentage of the sale to Stephen Leary to support further TF card developments and we also support our builders.
  • Timing fix is recommended on your A1200 motherboard. We can do this free of charge if you send your board to us (return shipping does need to be covered).
  • Cards sold as is, they are fully tested and a video will be shared of your card working before shipping.
  • We don't provide any advice or support for overclocking these cards, these are sold as 50Mhz. if you wish to overclock that is your choice. Heatsink and or fan required for overclocking.
 
£191.66 Ex. VAT Select options
Refurbished Amiga CD32
Refurbished Commodore Amiga CD32

Commodore Amiga CD32 - Professionally Refurbished

Technical Specifications:
  • Motorola 68020 (14Mhz) CPU
  • 2Mb Chip Ram
  • 2 x CD-Rom Drive
  • AGA Chipset
What's included?
  • Refurbished Amiga CD32 Unit
  • CD32 Controller
  • PSU (UK)
  What is refurbished? Each Commodore Amiga CD32 mainboard is professionally recapped (standard or Polymer is avilable at extra cost) and deep cleaned using a Ultrasonic cleaner, bathed using deionised water and professional grade PCB/Flux cleaning solution. Once completed it is dried and a full diagnostic test is completed. Each unit is thoroughly inspected make sure the Amiga CD32 works as it did when it first came from the factory back in the 1990’s. Case is cleaned but due to age may show signs of use and age. Checkout the work on the portfolio page here   Want up add some extras? We want you to have the Amiga you always wanted, and that’s why we can offer some great upgrades to your Amiga, for example: Extra fast ram for WHDLoad!   Shipping UK shipping will be via Parcelforce and shipping cost will be calculated the checkout. Worldwide shipping available simply contact us for a shipping quote.    

Images of the Amiga CD32 are for illustrative purposes only, each unit will show signs of age and use. If you want photos of the CD32's we have please contact us.

   
£549.99 Ex. VAT Select options
ACA500 Plus Enclousure/Case Amiga
ACA500Plus Individual Computers Amiga A500 A500 Plus
ACA500plus for the Amiga A500 and A500 Plus is the successor to the popular ACA500. The ACA500plus is an external expansion which is plugged to the left expansion port of your A500 or A500+. There is no need to open the computer at any time. This includes a new revolutionary method that can turn your 512k trapdoor memory expansion into chipram! If your Amiga is equipped with an ECS Agnus chip and said internal 512k memory expansion, you can turn your computer into a 1MByte-Chipram computer, just by selecting a menu item in the configuration menu of the ACA500plus! A lot of stock A500 computers with board revision 6 or higher have this exact configuration. The ACA500Plus houses a MC68HC000 processor clocked at 14.1MHz as standard, This will give your computer more than a double-speed boost. If that's not enough, you can choose overclocking to 21, 28 or even 42MHz. Overclocking success is not guaranteed. By attaching an ACA12xx or Blizzard 12xx accelerator, you can make your A500 faster than a stock A3000. The ACA500plus comes with essential software pre-installed in it's large flash. This includes fully licensed Kickstart versions V1.2 and V1.3 for backwards-compatibility, and Kickstart V3.1. You can install a fresh copy of Workbench 3.1 using the built in installer which is included within the ACA500Plus. All you need is an empty CF card, and you can install OS3.1 with a few key presses. After that's done, you can use the second CF card slot to exchange data with a modern PC: The ACA500plus supports PC-formatted cards and long filenames out of the box, no special installation required. CF cards are handled like hard disks on the Amiga-side. You can use HDtoolbox or HDinsttools - whatever you prefer. Even the two popular 64-bit addressing modes are implemented: Both TD64 and NSD64 command sets are supported, so whatever your preferred filesystem requires, you can use it on your ACA500plus setup to access flash cards that are larger than 4GBytes. Speed-wise, the CF card slots are faster than most hard disk controllers that are available for other Amiga computers. The ACA500plus even outperforms the SCSI controller of an A3000! Many users will want to use the ACA500plus with the popular WHDload software, which lets you install games on CF cards instead of swapping floppy disks if you want to play a different game. WHDload lists the 68010 processor as a minimum requirement for using the Quit-key and return to the Amiga's Workbench. The ACA500plus has special circuitry that lets you use the WHDload quit-key at any time, although you "only" have a 68HC000 processor. This is supported by WHDload V17.2 and higher. Advanced floppy control: If your computer has a defective or even a missing floppy drive, the ACA500plus can handle this. With the built-in "boot selector" circuitry, you can turn an external drive into a fully-compatible df0: drive. In addition to that, the floppy control functions allow you to make external drives invisible, although they do not have an off-switch. This saves you the work of (un)plugging drives in order to make older floppy-based software compatible. The ACA500plus features three expansion ports:
  1. A1200-compatible clockport
  2. local 16-bit expansion port
  3. A1200 CPU card connector
The A1200-compatible clockport can be used for expansions that were initially designed for the clockport of the A1200, for example Catweasel MK2, Delfina or RapidRoad. Please note that some drivers may require patching in order to work on a non-A1200 computer. Contact the vendor of your A1200 expansion to find out if they provide such a driver. The fast 16-bit local expansion port is reserved for our network expansion X-Surf-500. The A1200 CPU card connector is meant for further CPU and RAM upgrades. It is guaranteed to work with our ACA1220, ACA1221(ec, lc), ACA1232, ACA1233(n) and ACA1234 models. Our older ACA1230 accelerators are not supported. We will therefore only answer support questions about ACA1220, ACA1221(ec, lc), ACA1232, ACA1233(n) and ACA1234 accelerators. The same applies to old Blizzard accelerators by Phase 5: IComp have done their best to make them work, but there are limits to what we can do. Please keep in mind that the A500 is a 16-bit architecture, and the Blizzard accelerators have been developed for the 32-bit architecture of the A1200. Another new feature of the ACA500plus is it's capability to make use of a real time clock (RTC) that an A1200 accelerator provides. This keeps the clock port of the ACA500plus free for other uses. Further, an RTC that is located on the trapdoor expansion of your A500 can be used. This kind of flexibility was not available on the predecessor ACA500. With all these expansions, certain software may be incompatible. However, this is not a reason to unplug the ACA500plus, as it features an advanced cloaking mode that lets you downgrade the computer to standard memory configurations with minimal expansions (like Action Replay) or even no expansions at all, your choice of Kickstart ROM, running at the original 7MHz speed. Even if your computer does not have an internal 512k trapdoor memory expansion, the ACA500plus can not only add this, but even emulate the cycle-exact speed of the internal expansion with the same slow-down effects that an internal memory expansion has. In other words: There is no reason to unplug the ACA500plus at any time.   Package includes:
  • ACA500plus with DisMo, 68HC000, 8MB RAM, 8MB Flash
  • Short instruction manual German/English
  Software included in the flash ROM:
  • Kickstart V1.2, V1.3, V3.1
  • Full OS3.1 disk set with fully automatic installer
  • Action Replay 3 (patched for ACA500plus)
  • HRTmon
  • Thor's 040/060 libraries as resident modules
  • Thor's mmu and memory libraries
  • Network software, TCP/IP Stack for X-Surf-500
  Enclosure/Case is NOT included but available as an option.   Note: ** We don't support or advise the use of the Meanwell PSU or its variants unless its an original Amiga PSU l that has been recapped (better), AT PSU or the CA-PSU. The primary reason is the PSU is the heart of the Amiga and reading the Individual Computers forum, the PSU is the 2nd item to question if there are issues. The number one issue is the socket on the Indivision is not pushed down enough as it does require a lot of pressure. Full explanation regarding the PSU is here   If you have any questions just contact us  
£166.66 Ex. VAT Select options
CA-PSU Commodore Amiga Individual Computers
CA-PSU Amiga A500, A500 Plus, A600, A1200
CA-PSU Amiga A500, A500 Plus, A600, A1200 (CA-PSU stands for Compact Amiga Power Supply Unit), where "compact" designates the three target computers A500, A600 and A1200. It is the first power supply on the market that fully complies with the original Commodore specifications, introducing cable drop compensation for best regulation that even settles the voltage drop in the input filter of the target computers. This means that the voltage on the main 5V rail will never deviate more then 0.9%, measured inside the computer - no matter if the computer is in vanilla configuration or heavily expanded. Conventional power supplies will either supply too-high voltage to a vanilla machine, or too-low voltage to an expanded machine, causing malfunction or even defects. This cannot happen with our cable drop compensation technology. Technical data in short:
  • 5V, 5A, ripple/noise 50mV max. (typically 30mV)
  • Overload on 5V tolerated up to 8A for 30 seconds
  • 5V load regulation <0.6% typical, max. 0.9% under overload condition
  • 12V up to 4A
  • -12V, 0.1A
  • Modern, high-efficiency DC-DC converter technology
  • Total output power up to 60W
  • Fanless, silent, extremely low heat
CA-PSU is a two-brick solution: One mains-connected power brick and the CA-PSU converter box with the switch and square 5-pin DIN connector to the computer. This moves the power switch a lot closer to the computer, reducing the probability of inadvertent switching, for example if the power supply is under the table near your feet. CA-PSU has the best overall efficiency on the market, with a worst-case efficiency of 80.1% (best case >82.5%). The best competing product peaks at just over 70%, and some original Commodore power supplies have an efficiency of only 55%. This means that with our CA-PSU, there's less total heat, less power consumption and a longer life expectancy because there is less stress on the components. Naturally, CA-PSU features over-voltage protection - every modern power supply does. We wouldn't consider it worth mentioning, but this protection is part of a more complex block to protect your valuable classic gear: There are two critical moments that need to be taken care of: Switching on and off. CA-PSU has a controlled 5V ramp-up when switching on, ensuring safe power-up of heavily-expanded machines. Traditional power supplies without such a controlled start-up ramp tend to "swing in" to the target voltage, which might cause malfunction or even defects. Further, switching off will start a short timer, ensuring that the next switch-on event can't happen until a few seconds after switching off. This ensures that capacitors in the computer and expansion gear are sufficiently discharged, and switching on won't cause 3.3V regulators of modern expansions to oscillate, which may cause severe damage. In the unlikely event that these elaborate precautions fail, CA-PSU is covered by a German product liability insurance. This new production run of CA-PSU includes an international power brick that directly plugs into the socket (no mains cable). International adapters included are:
  • Central Europe
  • United Kingdom
  • Australia
  • USA
CA-PSU is compatible with worldwide grid voltages and frequencies (110-240V AC and 50 or 60Hz).  
£70.83 Ex. VAT Add to basket
Keyrah V3 for Commodore Amiga, Atari ST & PC
Keyrah V3 – Commodore Amiga, Atari ST, PC
Keyrah V3 allows you to connect original keyboards of classic computer systems like the Commodore 64 or the Amiga 1200 to modern computers (e.g. PC, Mac, or the Raspberry Pi) via USB. It also supports digital joysticks and analogue paddles of such classic systems, which will be converted to standard HID game controllers. Supported systems with this model are:
  • Commodore C64 (all models)
  • Commodore SX-64
  • Commodore VIC-20 (VC20)
  • Commodore C16
  • Commodore C128D
  • Amiga 1200
  • Amiga 600
  • Amiga 500
  • Amiga 4000/CDTV
  • Atari ST (8-pin connector only)
  • PC XT / PC AT (with PS/2 adapter)
The following systems can be made compatible by mounting additional connectors on the circuit board or using adapters:
  • Commodore C128
  • Commodore C116
  • Commodore plus/4
  • Commodore PET (8296)
  • Commodore CBM2 (B-Series)
  • Amiga 2000/3000 (with PS2 adapter)
Keyrah V3's switch allows you to switch between the standard and a keymap that's geared towards emulation. This switch looks and feels like the original power switch of the Commodore 64, adding a third switch position that allows you to send an ACPI signal to shut down/power up your computer. To avoid triggering the shutdown procedure by accident, this third position is not locked, so the switch will always flip back from it if not held in place. For further safety, the ACPI signal is only sent to the computer after being held in this position for five seconds. The box includes the Keyrah V3 circuit board and a printed manual. USB cable is not included. PCB colour will vary. [space_40]  
£49.99 Ex. VAT Add to basket
Amiga 1200 Premium Recapping Service
Amiga 4000 Recapping Service (Premium)
Amiga 4000 recapping service (Premium), all board revisions, NOTE this is NOT a repair service.
  • Check of the board before recapping is begun.
  • Removal of existing capacitors.
  • Cleanup and preparation of area.
  • Replace using Polymer Panasonic/Wurth/KEMET capacitors. (these will never leak)
  • Retest (Video, Audio, Floppy Boot, IDE).
 
£45.83 Ex. VAT Add to basket
Pistorm32-Lite CM4 Adaptor and Expansion board with HDMI, USB & Ethernet
PiStorm32-Lite CM4 Adaptor with Expansion Breakout
PiStorm32-Lite CM4 adaptor with expansion breakout with HDMI, Ethernet, USB. This is designed to be attached to the PiStorm32-lite adaptor to allow you add an Raspberry PI CM4 module. What's included:
  • CM4 Adapter (Allows connection of Expansion Breakout and Compute Module 4)
  • Passive Cooler
  • Expansion Breakout that provides HDMI, USB and Ethernet Ports
  • Flex wire 40Pin 20cm
  • Printed IO cover (3D printed)
  We also just sell the Pistorm32-Lite kits with Raspberry Pi 3A+ here
  NOTE: The PiStorm32-Lite CM4 product is an open source project and will require some knowledge of the  Amiga  
£74.99 Ex. VAT Read more
PiStorm32-Lite Rear Panel HDMI - USB & SD Card Slot
PiStorm32-Lite Rear Panel HDMI – USB – SD
PiStorm32-Lite Rear Panel which provides easy access to the internal PiStorm32-Lite HDMI, USB and SD card slot, negates the need to open up the A1200 trapdoor and access the SD card when updates are released.
The panel is 3D printed and available in:
  • White
  • Black
  • Gray
When purchasing, leave a note of the colour required.   Whats included:
  • Rear Panel
  • Micro HDMI Extension Cable
  • MicroSD Extension Cable
  • USB Extension Cable
  • M3 Screw and nut
  This is for the Pistorm32-Lite with Raspberry Pi3A+   Checkout the other great work the developer has created here  
£33.33 Ex. VAT Read more
Refurbished Amiga A600
Refurbished Commodore Amiga A600

Refurbished Commodore Amiga A600

Technical Specifications
  • Motorola 68000 (7.14Mhz) CPU
  • 1Mb Chip Ram
  • 2.04 Kickstart Roms
  • 3.5" Floppy Drive
  • UK Layout Keyboard
What’s included?
  • Professionally refurbished Amiga 600 Unit (excluding mouse and PSU), these are options that can be added.
  What is Refurbished? Each Commodore Amiga 600 mainboard is professionally recapped (standard or Polymer is avilable at extra cost) and deep cleaned using a Ultrasonic cleaner, bathed using deionised water and professional grade PCB/Flux cleaning solution. Once completed it is dried and a full diagnostic test is completed. Each unit is thoroughly inspected make sure the Amiga 600 worked as it did when it first came from the factory back in the 1990’s. Case and keyboard is stripped and cleaned but due to age may show signs of use and age.   What is Ultrasonic cleaning? Ultrasonic cleaning is a process that uses ultrasound (usually from 20–40 kHz) to agitate a fluid, this fluid is made up for this specific job which is to clean and remove any flux left over from recapping. We use deionised water (deionized depending where your from) and professional grade PCB cleaner. An example of the results and the process: [kad_youtube url="https://youtu.be/m4mbKPySfLE" ]   [caption id="attachment_17767" align="aligncenter" width="300"] Amiga Motherboard Before being Recapped & Ultrasonic Cleaned[/caption]   [caption id="attachment_17766" align="aligncenter" width="300"] Refurbished Amiga Motherboard - Recapped & Ultrasonic Cleaned[/caption] Want up add some extras? We want you to have the Amiga you always wanted, and that's why we can offer some great upgrades to your Amiga, for example: Extra fast ram for WHDLoad, Gotek drives etc.   Shipping UK shipping will be via Parcelforce and shipping cost will be calculated the checkout. Worldwide shipping available simply contact us for a shipping quote.   Ordering We only ask for a deposit and the rest upon completion.    

Images of the Amiga 600 is for illustrative purposes only, each unit will show signs of age and use. If you want photos of the Amiga 600 we have please contact us.

 
£329.99 Ex. VAT Select options
Replacement Amiga 500 PSU (Brand New)
Amiga CD32 PSU 50W Brand New
Amiga CD32 PSU, these are brand new and modern with It's 50W (55W peak) of total combined output power making it nearly 2x times stronger than original Commodore Amiga PSU and 2x smaller in dimensions & weight.
Key features:
  • Stabilized & filtered 5VDC up to 4A output (4.4A peak)
  • Stabilized & filtered 12VDC up to 2A output (2.2A peak)
  • Carefully calibrated for Amiga 500 reference load
  • Active & passive over voltage protection for main +5VDC line
  • Over current protection for all output lines
  • Fully isolated & fused on AC side
  • Power On/Off switch
  • Long output cable (1.8m) with circular DIN 5-pin plug.
  • Detachable input AC cable for all versions (cable included)
  • Weight only 0.4 KG (2x less than original PSU)
  • Runs COLD!
  • Safety standards: UL60950-1, TUV EN60950-1, ANSI/AAMI ES60601-1, TUV EN60601-1, IEC60601-1
  • Manufactured by Electroware
  • UK Stock
 
Warning! Risk of electrical shock and energy hazard when opened. All failures should be examined by a qualified technicians only. Risk of fire or electrical shock. The ventilation holes should be protected from foreign objects or dripping liquids. Please do not install power supplies in places with high ambient temperature or close to the heat source. Enclosed power supplies are intent to work in indoor locations, it's not allowed to use power supplies outdoor, in dust or high moisture. Output current and output wattage must not exceed the rated values. This replacement Amiga PSU has been designed for Commodore Amiga CD32 vintage computer systems only and should be considered as an integral component of Amiga computer system. Do not connect to any other devices as it's not a general purpose PSU. Manufacturer is not responsible for any consequences of unauthorised or arbitrary repairs, modifications or incorrect usage. Please notice that new, properly working replacement Amiga PSU is reducing the system's potential fail rate but still is not guaranteeing that entire Amiga system will work correctly (it's >30 years old).    
£45.83 Ex. VAT Read more
Amiga 600 1Mb Chip Ram Upgrade
Amiga A600 1Mb Chip Ram Memory Expansion
Amiga A600 1Mb Chip Ram upgrade fits in the trapdoor of the Amiga 600. These cards are brand new and perfect in giving your Amiga 600 a little boost and compliments the Amiga 600 8Mb Fast ram upgrade as 2Mb chip ram is recommended if your looking to start using WHDLoad. What is WHDLoad? WHDLoad is a a solution where by the user can install hundreds of Amiga games on to a HDD/CF or SD card even if the game originally did not have the option of installing the game on to the internal HDD/CF/SD card. The vast majority of games have already been converted ready to go or you can create them yourself if you have the original game on a floppy disk/s. Also many great Amiga demos have been converted for WHDLoad.   1 Year RTB Warranty.
£20.83 Ex. VAT Read more