Commodore Amiga

ACA1234 Amiga Accelerator
ACA1234 Amiga A1200 Accelerator 68030 128Mb Fast Ram
ACA1234 Amiga A1200 accelerator is the latest 68030 CPU based card from Individual Computers. This is far more than just another 68030 accelerator, it adds high-speed mass storage, improving the overall speed experience of your A1200 even more than the IDE speeder does, which is also available on this model. With 8MBytes of local flash memory and a local CF card slot, the ACA1234 is ideal for the hobbyist or power user. While iComps IDE speeder technology accelerates the onboard internal IDE port to raw transfer rates of up to 14MBytes/s (resulting in every-day performance of around 5MBytes/s with CF cards, or up to 9MB/s with physical hard drives), the ACA1234 onboard CF card slot can exceed 9MBytes/s. Other than competing products, both options do not require opening the computer or even removing chips from their socket. The IDE speedup to PIO mode 4 is activated with a software setting. NOTE: The IDE speeder feature is not available if connected to an ACA500Plus. The ACA1234 boards take memory performance to the limit of what a 68030 processor can transfer in a burst sequence: It's a sequence of four 32-bit transfers in four CPU cycles, You therefore get the best performance per MHz compared to other 68030 accelerators both modern and and legacy 68030 designs. In addition to that, the ACA1234 makes sure that the exec base in burst-capable, cacheable 32-bit fastmem. Another huge improvement over older accelerators is memory mapping to the legacy 0x00c0.0000 address. This is the location where many A500 games expect a trapdoor memory expansion. The ACA1234 cards give a good compatibility boost only because of this little chunk of memory in the right place. The ACA1234 is PCMCIA-friendly: It will not disable the onboard PCMCIA slot, so you can continue to use a networking card or a CF card adapter in that slot. For the easiest-possible transfer of files, drivers for a PCMCIA-CF card reader are included in the flash of this accelerator card. You can access PC-formatted and Amiga-formatted cards with ease, straight out of the box. you can even boot from a CF card in the PCMCIA slot.. Customers who are returning to the "hobby Amiga" often have the problem of lost installation disks, or even a defective floppy drive after all these years. Installing a system becomes almost impossible in such cases. The ACA1234 includes media to install a system in such a case as well: Both ROM and install disks (Workbench 3.1) are licensed from Hyperion and included in the flash of the ACA1234. The installer, which has been successfully used with the ACA500Plus and Buddha Plus One IDE Controller as well, installs a system way faster than it will ever be possible with floppy drives - and it only take a few mouse clicks. This includes automatic partitioning of media that's larger than 4GBytes! All features
  1. 127 MByte RAM auto-configuration
  2. 1 MByte RAM reserved for fast Kickstart re-mapping (you can also kickstart from other roms including 3.2).
  3. 8 MByte flash for installation files and Kickstart ROMs
  4. Local CF card slot as high-speed mass storage
  5. IDE speeder technology for read and write
  6. Drivers for PCMCIA-CF card reader in flash
  7. ROM and OS 3.1 in flash, extremely fast system installation
  8. Clock rate can be reduced (reset required)
  9. Card enable/disable in software without power-cycling
  10. Faster clockport gives 55% speed increase
  11. Field-proven high A1200 compatibility
Memory of the ACA1234 is auto-configuring. This means that all memory is available from a power-up without installing any software on the computer. If you do not require full speed, the card can be slowed down in order to save power or reduce heat. You can also increase the speed beyond rated clock rate for a trial period - if you find that your CPU can accept a certain level of overclocking, you can purchase a permanent overclocking license. Some software does not like accelerated execution. For these cases, the ACA1234 can be switched off and put into a "stealth mode": This will allow you to run such software without having to remove the accelerator. Returning to 68030 operation does not require the computer to be power-cycled. The clockport of the ACA1234 can either take an RTC module, or a different clock port device. Operation of such a clock port device is 55% faster than with the internal clock port of the A1200 computer, provided the drivers support the address of this port. This function is available in all modes of operation on an A1200 computer, and on select ACA500plus models with updated CPLD. Last not least, the ACA1234 features iComp's field-proven A1200 motherboard interface. Some A1200 main boards have been delivered with the wrong timing components and require modification for reliable use with accelerators. With our interface, the ACA1234 is less likely to require these board patches. Although the ACA1234 will work reliably with any patch level of the A1200 main board, you may still want to perform these patches, as they also fix graphics glitches with Super-Hires resolutions of the AGA chipset.   Package contains:
  • Accelerator with RAM and CPU assembled
  • Short installation manual
You will need in addition to that:
  • Motherboard patches as described by Commodore: A1200 capacitors E123C and E125C may need to be removed.
  • A proper power supply that provides good regulation, even when loaded with expansions like the CA-PSU
  • If desired, a PCMCIA-CF card reader
  Processors on this card are used and have scratches.   Image showing the ACA1234 50Mhz version. 25Mhz CPU is copper top. 33Mhz is a black ceramic CPU    
£233.33 Ex. VAT Select options
A630 REV3 Amiga A600 Accelerator 68030 - FPU - 64Mb - Purple Edition
A630 Accelerator Amiga A600 68030 50Mhz, 128Mb, FPU PURPLE
A630 Accelerator Amiga A600 68030 50Mhz inc FPU PURPLE EDITION is the latest revision of the A630 modern turbo card with the classic 68030 Motorola processor running at 50Mhz and also includes an onboard FPU. Perfect for that sweet spot in speed and usefulness for Demos, WHDLoad* gaming, internet and so on. This will give any A600 a great speedboost in a compact unit. Full specs:
  • CPU MC68030, clocked on 50MHz.
  • FPU 68882FN40 - synchronous or asynchronous clocking.
  • 128MB SDRAM Fast Ram.
  • Cooling: Active included.
  • PCMCIA Friendly.
  • PCB Colour - Purple
 
Important Information:
 
MMULib's for the A630 Accelerator
The A630 Accelerator requires the installation of MMULib's and it very important you use the right ones for the kickstart ROM you are using: 3.1 Kickstart: http://main.aminet.net/util/libs/MMULib.lha http://main.aminet.net/util/libs/MMULib.readme 3.2, 3.2.1 or 3.2.2   Install the MMULib package that came with the installation CD ONLY and NOT the ones from Aminet.  
Notes:
  • Some demos or games may require disable "CPU CACHE" for better compatibility with the MC68000.
  • The card is designed to work with 3.1 Roms and above including 3.2 and 3.2.1 of which can be  purchased below.
  • An internal HDD/CF/SD Card needs to be installed for the A630 to boot.
  *2Mb Chip ram is strongly recommended for WHDLoad which is available here    
£224.99 Ex. VAT Add to basket
A630 Rev 3 Amiga 600 Accelerator
A630 Rev 3 128Mb Accelerator 68030 50Mhz / FPU Amiga A600
A630 Rev 3 128Mb Accelerator for the Amiga 600 is the latest revision of the A630 modern turbo card with the classic 68030 Motorola processor running at 50Mhz and also includes an onboard FPU and has 128Mb Fast ram. Perfect for that sweet spot in speed and usefulness for Demos, WHDLoad* gaming, internet and so on. This will give any A600 a great speedboost in a compact unit. Full specs:
  • CPU MC68030, clocked on 50MHz.
  • FPU 68882FN40 - synchronous or asynchronous clocking
  • 128MB SDRAM Fast Ram.
  • Cooling: Passive or Active. No heatsink or fan is included, options are below.
  • PCMCIA Friendly.
 
Important Information:
 
MMULib's for the A630 Accelerator
The A630 Accelerator requires the installation of MMULib's and it very important you use the right ones for the kickstart ROM you are using: 3.1 Kickstart: http://main.aminet.net/util/libs/MMULib.lha http://main.aminet.net/util/libs/MMULib.readme 3.2, 3.2.1 or 3.2.2   Install the MMULib package that came with the installation CD ONLY and NOT the ones from Aminet.  
Notes:
  • Some demos or games may require disable "CPU CACHE" for better compatibility with the MC68000.
  • The card is designed to work with 3.1 Roms and above including 3.2 and 3.2.1 of which can be  purchased below.
  • The Oscillator will need some insulation tape put on top to stop the A630 touching it.
  • PCB Colour will vary.
  *2Mb Chip ram is strongly recommended for WHDLoad which is available here   {PCB Colour will vary)    
£216.66 Ex. VAT Read more
A630 Rev 3 Amiga 600 Accelerator
A630 Rev 3 Accelerator 68030 50Mhz 64Mb FPU Amiga A600
A630 Rev 3 Accelerator for the Amiga 600 is the latest revision of the A630 modern turbo card with the classic 68030 Motorola processor running at 50Mhz and also includes an onboard FPU. Perfect for that sweet spot in speed and usefulness for Demos, WHDLoad* gaming, internet and so on. This will give any A600 a great speedboost in a compact unit. Full specs:
  • CPU MC68030, clocked on 50MHz.
  • FPU 68882 - synchronous or asynchronous clocking.
  • 64MB SDRAM Fast Ram.
  • Cooling: Active included.
  • PCMCIA Friendly.
 
Important Information:
 
MMULib's for the A630 Accelerator
The A630 Accelerator requires the installation of MMULib's and it very important you use the right ones for the kickstart ROM you are using: 3.1 Kickstart: http://main.aminet.net/util/libs/MMULib.lha http://main.aminet.net/util/libs/MMULib.readme 3.2, 3.2.1 or 3.2.2   Install the MMULib package that came with the installation CD ONLY and NOT the ones from Aminet.  
Notes:
  • Some demos or games may require disable "CPU CACHE" for better compatibility with the MC68000.
  • The card is designed to work with 3.1 Roms and above including 3.2 and 3.2.1 of which can be  purchased below.
  • An internal HDD/CF/SD Card needs to be installed for the A630 to boot.
  • PCB Colour will vary.
  *2Mb Chip ram is strongly recommended for WHDLoad which is available here    
£208.33 Ex. VAT Read more
Refurbished Amiga A500
Refurbished Commodore Amiga 500 Unit

Commodore Amiga A500 – Professionally Refurbished & Recapped

Technical Specifications
  • Motorola 68000 (7.14Mhz) CPU
  • 1Mb Chip Ram
  • 1.3 Kickstart Rom
  • 3.5" Floppy Drive
  • UK Layout Keyboard
What’s included?
  • Professionally refurbished Amiga A500 Unit (excluding mouse and PSU), these are options that can be added.
  What is Refurbished? Each Commodore Amiga A500 mainboard is professionally recapped and deep cleaned using a Ultrasonic cleaner, bathed using deionised water and professional grade PCB/Flux cleaning solution. Once completed it is dried and a full diagnostic test is completed. Each unit is thoroughly inspected make sure the Amiga 500 worked as it did when it first came from the factory back in the 1980’s. Case and keyboard is stripped and cleaned but due to age may show signs of use and age. It can take up to 21 working days for machines to be completed due to the high volume of orders, please take this into account when ordering.   What is Ultrasonic cleaning? Ultrasonic cleaning is a process that uses ultrasound (usually from 20–40 kHz) to agitate a fluid, this fluid is made up for this specific job which is to clean and remove any flux left over from recapping. We use deionised water (deionized depending where your from) and professional grade PCB cleaner. An example of the results: [caption id="attachment_17767" align="aligncenter" width="300"] Amiga Motherboard Before being Recapped & Ultrasonic Cleaned[/caption]   [caption id="attachment_17766" align="aligncenter" width="300"] Refurbished Amiga Motherboard - Recapped & Ultrasonic Cleaned[/caption] Want up add some extras? We want you to have the Amiga you always wanted, and that's why we can offer some great upgrades to your Amiga, for example: Extra fast ram for WHDLoad, Gotek drives etc.   Shipping UK shipping will be via Parcelforce and shipping cost will be calculated the checkout. Worldwide shipping available simply contact us for a shipping quote.    

Images of the Amiga A500 is for illustrative purposes only, each unit will show signs of age and use. If you want photos of the Amiga 500 we have please contact us.

  As these are custom built they can take between 21/28 working days depending on what add-ons are added and workload. So please do not order if you are not able to wait - Deposits are not refundable
£249.99 Ex. VAT Select options
ACA500 Plus Enclousure/Case Amiga
ACA500Plus Individual Computers Amiga A500 A500 Plus
ACA500plus for the Amiga A500 and A500 Plus is the successor to the popular ACA500. The ACA500plus is an external expansion which is plugged to the left expansion port of your A500 or A500+. There is no need to open the computer at any time. This includes a new revolutionary method that can turn your 512k trapdoor memory expansion into chipram! If your Amiga is equipped with an ECS Agnus chip and said internal 512k memory expansion, you can turn your computer into a 1MByte-Chipram computer, just by selecting a menu item in the configuration menu of the ACA500plus! A lot of stock A500 computers with board revision 6 or higher have this exact configuration. The ACA500Plus houses a MC68HC000 processor clocked at 14.1MHz as standard, This will give your computer more than a double-speed boost. If that's not enough, you can choose overclocking to 21, 28 or even 42MHz. Overclocking success is not guaranteed. By attaching an ACA12xx or Blizzard 12xx accelerator, you can make your A500 faster than a stock A3000. The ACA500plus comes with essential software pre-installed in it's large flash. This includes fully licensed Kickstart versions V1.2 and V1.3 for backwards-compatibility, and Kickstart V3.1. You can install a fresh copy of Workbench 3.1 using the built in installer which is included within the ACA500Plus. All you need is an empty CF card, and you can install OS3.1 with a few key presses. After that's done, you can use the second CF card slot to exchange data with a modern PC: The ACA500plus supports PC-formatted cards and long filenames out of the box, no special installation required. CF cards are handled like hard disks on the Amiga-side. You can use HDtoolbox or HDinsttools - whatever you prefer. Even the two popular 64-bit addressing modes are implemented: Both TD64 and NSD64 command sets are supported, so whatever your preferred filesystem requires, you can use it on your ACA500plus setup to access flash cards that are larger than 4GBytes. Speed-wise, the CF card slots are faster than most hard disk controllers that are available for other Amiga computers. The ACA500plus even outperforms the SCSI controller of an A3000! Many users will want to use the ACA500plus with the popular WHDload software, which lets you install games on CF cards instead of swapping floppy disks if you want to play a different game. WHDload lists the 68010 processor as a minimum requirement for using the Quit-key and return to the Amiga's Workbench. The ACA500plus has special circuitry that lets you use the WHDload quit-key at any time, although you "only" have a 68HC000 processor. This is supported by WHDload V17.2 and higher. Advanced floppy control: If your computer has a defective or even a missing floppy drive, the ACA500plus can handle this. With the built-in "boot selector" circuitry, you can turn an external drive into a fully-compatible df0: drive. In addition to that, the floppy control functions allow you to make external drives invisible, although they do not have an off-switch. This saves you the work of (un)plugging drives in order to make older floppy-based software compatible. The ACA500plus features three expansion ports:
  1. A1200-compatible clockport
  2. local 16-bit expansion port
  3. A1200 CPU card connector
The A1200-compatible clockport can be used for expansions that were initially designed for the clockport of the A1200, for example Catweasel MK2, Delfina or RapidRoad. Please note that some drivers may require patching in order to work on a non-A1200 computer. Contact the vendor of your A1200 expansion to find out if they provide such a driver. The fast 16-bit local expansion port is reserved for our network expansion X-Surf-500. The A1200 CPU card connector is meant for further CPU and RAM upgrades. It is guaranteed to work with our ACA1220, ACA1221(ec, lc), ACA1232, ACA1233(n) and ACA1234 models. Our older ACA1230 accelerators are not supported. We will therefore only answer support questions about ACA1220, ACA1221(ec, lc), ACA1232, ACA1233(n) and ACA1234 accelerators. The same applies to old Blizzard accelerators by Phase 5: IComp have done their best to make them work, but there are limits to what we can do. Please keep in mind that the A500 is a 16-bit architecture, and the Blizzard accelerators have been developed for the 32-bit architecture of the A1200. Another new feature of the ACA500plus is it's capability to make use of a real time clock (RTC) that an A1200 accelerator provides. This keeps the clock port of the ACA500plus free for other uses. Further, an RTC that is located on the trapdoor expansion of your A500 can be used. This kind of flexibility was not available on the predecessor ACA500. With all these expansions, certain software may be incompatible. However, this is not a reason to unplug the ACA500plus, as it features an advanced cloaking mode that lets you downgrade the computer to standard memory configurations with minimal expansions (like Action Replay) or even no expansions at all, your choice of Kickstart ROM, running at the original 7MHz speed. Even if your computer does not have an internal 512k trapdoor memory expansion, the ACA500plus can not only add this, but even emulate the cycle-exact speed of the internal expansion with the same slow-down effects that an internal memory expansion has. In other words: There is no reason to unplug the ACA500plus at any time.   Package includes:
  • ACA500plus with DisMo, 68HC000, 8MB RAM, 8MB Flash
  • Short instruction manual German/English
  Software included in the flash ROM:
  • Kickstart V1.2, V1.3, V3.1
  • Full OS3.1 disk set with fully automatic installer
  • Action Replay 3 (patched for ACA500plus)
  • HRTmon
  • Thor's 040/060 libraries as resident modules
  • Thor's mmu and memory libraries
  • Network software, TCP/IP Stack for X-Surf-500
  Enclosure/Case is NOT included but available as an option.   Note: ** We don't support or advise the use of the Meanwell PSU or its variants unless its an original Amiga PSU l that has been recapped (better), AT PSU or the CA-PSU. The primary reason is the PSU is the heart of the Amiga and reading the Individual Computers forum, the PSU is the 2nd item to question if there are issues. The number one issue is the socket on the Indivision is not pushed down enough as it does require a lot of pressure. Full explanation regarding the PSU is here   If you have any questions just contact us  
£199.99 Ex. VAT Select options
A630 REV3 Amiga A600 Accelerator 68030 - FPU - 64Mb - Purple Edition
A630 Rev 3 Accelerator 68030 50Mhz, 64Mb, FPU Amiga A600 PURPLE

A630 Rev 3 68030 50Mhz inc FPU Amiga A600 PURPLE EDITION is the latest revision of the A630 modern turbo card with the classic 68030 Motorola processor running at 50Mhz and also includes an onboard FPU. Perfect for that sweet spot in speed and usefulness for Demos, WHDLoad* gaming, internet and so on. This will give any A600 a great speedboost in a compact unit.

Full specs:

  • CPU MC68030, clocked on 50MHz.
  • FPU 68882FN40 – synchronous or asynchronous clocking.
  • 64MB SDRAM Fast Ram.
  • Cooling: Active included.
  • PCMCIA Friendly.
  • PCB Colour – Purple

 

Important Information:

 

MMULib’s for the A630 Accelerator

The A630 Accelerator requires the installation of MMULib’s and it very important you use the right ones for the kickstart ROM you are using:

3.1 Kickstart:

http://main.aminet.net/util/libs/MMULib.lha
http://main.aminet.net/util/libs/MMULib.readme

3.2, 3.2.1 or 3.2.2  

Install the MMULib package that came with the installation CD ONLY and NOT the ones from Aminet.

 

Notes:
  • Some demos or games may require disable “CPU CACHE” for better compatibility with the MC68000.
  • The card is designed to work with 3.1 Roms and above including 3.2 and 3.2.1 of which can be  purchased below.
  • An internal HDD/CF/SD Card needs to be installed for the A630 to boot.

 

*2Mb Chip ram is strongly recommended for WHDLoad which is available here

 

 

£199.99 Ex. VAT Read more
TF536 A500, A500+ Amiga Accelerator
TF536 Accelerator for Amiga 500/2000
TF536 accelerator a perfect upgrade for any Amiga A500, 500+ or A2000. Included is a gold top Motorola 68030 CPU clocked at 50mhz, 64MB of RAM, and a 2.5" IDE connector for an CF HDD Card. Full specs:
  • MC68030RC50C Processor
  • 64MByte of fast-ram.
  • 44 Pin IDE connector
  • Includes A500/A500+ CPU relocator
Prerequisites 
  • Kickstart ROM 3.1, 3.1.4, 3.2 to boot from IDE (available as an option below).
What is TerribleFire?
Well it’s not what it’s who, and that person is Stephen Leary who has designed a whole host of accelerators and ram cards for the Amiga A500, A1200 and Amiga CD32. These include many but the most common ones are:
£195.83 Ex. VAT Read more
Indivision MK3 AGA for Amiga A1200 and A4000T
Indivision AGA MK3 Flickerfixer for A1200 and A4000T
Indivision AGA MK3 for the A1200 and A4000T* (Not A4000D Desktop) providing both a VGA connection or HDMI so you have the flexibility of using a CRT/LCD PC monitor with VGA or a large TV with HDMI in. All Amiga screen modes are supported and can be sent to a digital or analogue monitor at almost any frame rate (with the exception of A2024 monitor modes). Either using standard VESA modes or using custom output frequencies and size at the user's choice. Even custom screen modes like HighGFX can be used. Workbench resolutions of 1280x1024 pixels are possible without buying a dedicated graphics card. Indivision AGA Mk3 is plugged over the Lisa chip and a second connection over the CIA chip to route keyboard signals to the flicker fixer. You can now make small adjustments to the output picture format including positioning and resizing of the output picture without the need to load the configuration tool. You can simply open the on screen menu using a hot-key combination make adjustments with the keyboard or mouse and then exit this live configuration menu, all this without leaving the game or demo that's currently running. Output screen modes can be saved "per input screen mode", so you can adjust your favourite Workbench resolution perfectly, while not affecting the settings you've chosen for PAL and NTSC games. Settings are saved in the flash of the flicker fixer, so they survive a reboot and/or power-cycle of the computer this allows you to "zap" through pre-sets that are ideal for a specific game or demo. With this you can adjust on the fly different settings for the built-in scanline effect, or you can compare the scaling capabilities of your monitor with the new built-in scaler of Indivision AGA MK3. The Indivision also has automatic monitor recognition, the configuration tool can detect what size of monitor is connected and make suggestions for ideal output frequencies that are within the specifications of the monitor. This reduces the "first setup" to a matter of minutes, maybe even seconds if you're using one of the pre-sets for popular display panel sizes that we provide.   What's included:
  1. Indivision AGA Mk3 for A1200/A4000T(*)
  2. Adapter board for high-definition digital (HDMI) and VGA output
  3. Adapter board for CIA chip
  4. Connection cables between all boards
  5. Short instructions
In addition, you will require:
  1. Screwdriver to open your computer
  2. A way to transfer the configuration tool (free download from our wiki)
  3. HighGFX software package from Aminet (free download for higher Workbench resolutions)
    (*)This flickerfixer will not fit into an A4000T out-of-the-box. Component CE164C gets in the way of the output cable connector and must be replaced with a lower-profile version prior to installing the flickerfixer. We recommend to do this before you order the product.   Note: ** We don't support or advise the use of the Meanwell PSU or its variants unless its an original Amiga PSU l that has been recapped (better), AT PSU or the CA-PSU. The primary reason is the PSU is the heart of the Amiga and reading the Individual Computers forum, the PSU is the 2nd item to question if there are issues. The number one issue is the socket on the Indivision is not pushed down enough as it does require a lot of pressure. Full explanation regarding the PSU is here   If you have any questions just contact us   Pictures vary, PCB colour is purple.
£191.66 Ex. VAT Read more
TF1260 TerribleFire A1200 Accelerator
TF1260 TerribleFire A1200 Accelerator – NO CPU
TF1260 TerribleFire Amiga 1200 Accelerator which hosts 64Mb Fast Ram, IDE connector (DOES NOT INCLUDE 68060 PROCESSOR). The TF1260 is one of the best 060 accelerators you can purchase for the Amiga 1200 And is the next step up after the TF1230 A1200 Accelerator add-on we sell for those that want that large speed jump. Full specs:
  • 128MByte of fast-ram.
  • IDE Interface - Driver required - ehide.device
  • Compatible with any A1200 motherboard revision.
  • Fits in your old/new stock A1200 case!!!
  • Just add your choice of 68060 processor!
  Processor support: The TF1260 TerribleFire supports all genuine 68060 processors including:
  • MC68060RC50 or XC68060RC50 (Complete with MMU & FPU)
  • MC68LC060RC50 or XC68LC060RC50 (MMU No FPU)
  • MC68EC060RC50 or XC68EC060RC50 (No MMU or FPU)
Only purchase this card if you know you have a genuine 68060 processor, The low end versions that have no MMU or FPU are more often genuine.   Prerequisites 
  • Timing fix is strongly recommended on your A1200 motherboard. We can do this free of charge if you send your board to us (return shipping does need to be covered).
  • Kickstart ROM 3.1, 3.1.4, 3.2, 3.x or 3.9 (not compatible with 3.0).
  What is Terriblefire? Well it's not what it's who, and that person is Stephen Leary who has designed a whole host of accelerators and ram cards for the Amiga A500, A1200 and Amiga CD32. These include many but the most common ones are:   NOTES:
  • For every TF1260 sold we donate a percentage of the sale to Stephen Leary to support further TF card developments and we also support our builders.
  • Timing fix is recommended on your A1200 motherboard. We can do this free of charge if you send your board to us (return shipping does need to be covered).
  • Cards sold as is, they are fully tested and a video will be shared of your card working before shipping.
  • We don't provide any advice or support for overclocking these cards, these are sold as 50Mhz. if you wish to overclock that is your choice. Heatsink and or fan required for overclocking.
 
£191.66 Ex. VAT Read more
Indivision MK3 AGA for Amiga A1200 and A4000T
Indivision AGA MK3 Flickerfixer for Amiga CD32 and A4000D
Indivision AGA MK3 flickerfixer for Amiga CD32** and A4000D (also available for the Amiga A1200 and A4000T). For installation in an A4000D, a jumper needs to be bent aside (see further down). Sporting both a VGA and HDMI socket (not used at the same time) and a fully digital output which lets you connect to a modern TV or a DVI monitor. Finally, you can connect your favourite computer to a modern flat screen and use super-hires resolutions on your workbench in full colour! Indivision AGA MK3 does everything that it's predecessors did and much more! With the only exception of A2024 monitor modes, all Amiga screen modes are supported and can be sent to a digital or analogue monitor at almost any frame rate, either using standard VESA modes, or using custom output frequencies and size at the user's choice. Even custom screen modes like HighGFX can be used: Workbench resolutions of 1280x1024 pixels are possible without buying a graphics card. Further, Indivision AGA MK3 supports synchronisation of the output signal with the computer's V-Sync signal, which was not possible with the predecessor models. This allows silky-smooth animations and perfect scrolling without tearing. These fully synchronised modes may not be compatible with all VGA- or DVI monitors (mainly because they are 50Hz for PAL machines), but 50Hz is standard for all TVs with high-definition digital input. Indivision AGA Mk3 is plugged over the Lisa chip. For the first time, a second (optional!) connection is required to take advantage of all features of the product: An additional adapter is clipped on top of a CIA chip to route keyboard signals to the flicker fixer. This gives way for a huge practical improvement over previous versions of the flicker fixer: You can now make small adjustments to the output picture format, including positioning and resizing of the output picture without the need to load the configuration tool. You can now open a simple menu using a hot-key combination, make adjustments with the keyboard or mouse and then exit this live configuration menu - all this without leaving the game or demo that's currently running. Output screen modes can be saved "per input screen mode", so you can adjust your favourite Workbench resolution perfectly, while not affecting the settings you've chosen for PAL and NTSC games. Settings are saved in the flash of the flicker fixer, so they survive a reboot and/or power-cycle of the computer. As opposed to Indivision AGA MK2, more than one output mode can be saved, and instead of making manual adjustments using the live configuration menu described before, you can just "zap" through pre-sets that are ideal for a specific game or demo. This allows you to see the difference of intensity settings for the built-in scanline effect, or you can compare the scaling capabilities of your monitor with the new built-in scaler of Indivision AGA MK3. Another improvement over the predecessor is automatic monitor recognition: The configuration tool can detect what size of monitor is connected and make suggestions for ideal output frequencies that are within the specifications of the monitor. This reduces the "first setup" to a matter of minutes. Whats included:
  1. Flickerfixer for A4000D(*)/CD32(**)
  2. Adapter board for high-definition digital and VGA output
  3. Adapter board for CIA chip
  4. Connection cables between all boards
  5. Stainless steel back plate for HDMI/VGA output
  6. Short instructions
  7. A transfer method for the configuration tool (free download from individual Computers wiki)
  8. (Optional) HighGFX software package from Aminet (free download for higher Workbench resolutions)
  (*)This flickerfixer will only fit into an A4000D after jumper J214 has been bent aside. This jumper was meant for a future chipset that was never released. (**)For installation in a CD32, live config is only available if three solder-connections have been made, as this model does not have CIA chips. For accurate audio filter reproduction on HDMI TVs, a fourth solder connection must be made. Further, it was reported that select main boards of the CD have the crystal oscillator very close to the Lisa chip, requiring the user to move the part to the side by a fraction of a millimeter. A soldering iron may be required to accomplish this.    
£183.33 Ex. VAT Add to basket
PiStorm32-Lite CM4 Module Bundle
PiStorm32-Lite CM4, Expansion Breakout & 64Gb SD Card Bundle
PiStorm32-Lite CM4 bundle with Raspberry Pi CM4 module, expansion breakout with HDMI, Ethernet, USB and 64Gb SD Card. This is fully assembled, just installed Workbench. What's included:
  • Pistorm32-Lite adapter
  • CM4 Adapter (Allows connection of Expansion Breakout and Compute Module 4)
  • Raspberry Pi CM4 module with Wifi (Supports AmiKit also)
  • Passive Cooler
  • Expansion Breakout that provides HDMI, USB and Ethernet Ports
  • SD Card 64GB Sandisk Ultra (pre installed EMU68 on 200MB partition) Optional upgrade to AmiKit Pistorm edition*
  • Flex wire 40 Pin 20cm
  • Printed IO cover (3D printed)
   

Now with an added option of AmiKit and AmigaOS 3.2.2 plug and play options*. Now with WiFI**!

AmiKit PiStorm32 SD Card
  NOTE: The PiStorm32-Lite CM4 product is a open source project and will require some knowledge of the Amiga. *AmiKit Pistorm Edition requires AmigaOS 3.2 installation disks (ADF) and an internet connection, full details here. ** Wifi (wifipi.device) is still in alpha, which means that it can (and will) contain bugs. For this version you need to set up an unencrypted 2.4GHz wireless network (without a password). However, you can hide it in your router settings so that no one else can see it and connect to it. Future versions will bring WPA/WPA2 encryption.  
£166.66 Ex. VAT Read more