Replacement Amiga 500 PSU (Brand New)
Commodore Amiga PSU for A1200
Commodore Amiga PSU for A1200, these are brand new and modern with It's 50W (55W peak) of total combined output power making it nearly 2x times stronger than original Commodore Amiga PSU and 2x smaller in dimensions & weight.
Key features:
  • Stabilized & filtered 5VDC up to 4A output (4.4A peak)
  • Stabilized & filtered 12VDC up to 2A output (2.2A peak)
  • Stabilized & filtered -12VDC up to 0.5A output (0.55A peak)
  • Carefully calibrated for Amiga 500 reference load
  • Active & passive over voltage protection for main +5VDC line
  • Over current protection for all output lines
  • Fully isolated & fused on AC side
  • Power On/Off switch
  • Long output cable (1.8m) with rectangular DIN 5-pin plug.
  • Detachable input AC cable for all versions (cable included)
  • Weight only 0.4 KG (2x less than original PSU)
  • Runs COLD!
  • Safety standards: UL60950-1, TUV EN60950-1, ANSI/AAMI ES60601-1, TUV EN60601-1, IEC60601-1
  • Manufactured by Electroware
  • UK Stock
 
Warning! Risk of electrical shock and energy hazard when opened. All failures should be examined by a qualified technicians only. Risk of fire or electrical shock. The ventilation holes should be protected from foreign objects or dripping liquids. Please do not install power supplies in places with high ambient temperature or close to the heat source. Enclosed power supplies are intent to work in indoor locations, it's not allowed to use power supplies outdoor, in dust or high moisture. Output current and output wattage must not exceed the rated values. This replacement Amiga PSU has been designed for Commodore Amiga 1200 vintage computer systems only and should be considered as an integral component of Amiga computer system. Do not connect to any other devices as it's not a general purpose PSU. Manufacturer is not responsible for any consequences of unauthorised or arbitrary repairs, modifications or incorrect usage. Please notice that new, properly working replacement Amiga PSU is reducing the system's potential fail rate but still is not guaranteeing that entire Amiga system will work correctly (it's >30 years old).    
 £ 45.83 Excl. VAT Add to basket
Amiga Gotek FlashFloppy OLED Header
Amiga 1200 Gotek Drive (Flashfloppy) with Mount, OLED Header
Amiga 1200 Gotek drive pre-installed with FlashFloppy, these Gotek drives are based on a more modern OpenFlops floppy emulator which provides many improvements over the original Gotek drive, these units are a great replacement for your failing Amiga 1200 floppy drive or you wish to simply replace your current 3.5" floppy drive. These are plug and play in that you simply remove your existing Amiga 1200 floppy drive and replace it with this unit (you use your existing bracket). 3 new screws will also be supplied to secure it to the Amiga 1200. The Amiga 1200 Gotek drive also comes with an OLED Header unit will need 4 wires passing through the vent, the end plastic boots will be supplied so you add them after you have passed them through the vent. This provides easy viewing of what game or program you wish to use. You will need a USB stick (any size) formatted as FAT32. You can add a pre-configured USB stick as an option below.
What's included:
  • OpenFlops Gotek Drive
  • 3D Printed Amiga 1200 Gotek Mount
  • OLED Display with 3D Printed Header
[hr]
What is OpenFlops Gotek Drive?
OpenFlops is an Open Hardware implementation of such an emulator, inspired from the ubiquitous Gotek hardware. It is designed to run the FlashFloppy firmware, which gives it several improvements over the original Gotek: Further information on what a gotek drive is can be found here    
 £ 37.49 Excl. VAT Read more
Amiga 1200 Gotek, FlashFloppy, 3D Printed Mount
Amiga 1200 Gotek Drive, Printed Mount, OLED Display and FlashFloppy
Amiga 1200 Gotek drive is a great replacement for your failing Amiga 1200 floppy drive or you wish to simply replace it with a Gotek drive. These are plug and play and come pre flashed with FlashFloppy in that you simply remove your existing floppy drive and replace it with this unit (you use your existing bracket). 3 new screws will also be supplied to secure the Gotek drive to your Amiga. You will need a USB memory stick (NOT included) with your loaded ADF files but we offer an option for a pre-configured USB stick below.
What are ADF files?
ADF files is the standard Amiga Disk Format for floppy disk images. no different to Sega or Nintendo roms, ADF's are images of Amiga floppy disk games. Not only could you have access to a huge back catalogue of retro Amiga games, but there are still brand new games being released today, for example: Raid over Moscow or Bridge Strike these are all available as ADF files. But you not limited to games or programs, but you have access to tons of Amiga demos (if your into that scene).
What are gotek drives in detail? Read here What is FlashFloppy check out this link Want to know even more about them, checkout retro32.com's review of them here Also checkout one of our favorite youtube streamers TheGebs24 and her views on the Gotek drive!
 £ 33.33 Excl. VAT Read more
Amiga A1200 HDISK/FDISK LED Adaptor
Amiga A1200 HDISK/FDISK LED Adapter
Amiga A1200 HDISK/FDISK LED adapter provides 2 separate inputs to show the activity of and not limited to, Icedrake V4, PiStorm32-Lite SD slot, hard drives or PCMCIA port using the original LED module on the Amiga 1200 LED panel. Signals for the internal HDD and DISK are transmitted as is, also this module corrects the constant LED light that may occur with some SD or CompactFlash cards. There are also LEDs on the module itself that show floppy and hard drive activity. This can be especially useful when the Amiga 1200 is operated without the original keyboard. Configuration  There are a total of 2 pins available on  J3  , which have the following characteristics.
  • A  = HDD input - (output via HDISK LED)
  • B  = FDD input - (output via FDISK LED)
  So for example you want to show the PCMCIA activity, you would connect a wire to the FDD input and any PCMCIA activity will show via the FDISK LED.   NOTE: Soldering skills will be required when connecting 3rd party activity signals to the Amiga A1200 HDISK/FDISK LED adapter, more details to follow.  
 £ 10.83 Excl. VAT Add to basket
Amiga Gotek Drive inc Amstrad, Spectrum, Atari, IBM PC
Gotek Drive pre-flashed with FlashFloppy (Generic)
Gotek drive is a inexpensive solution to replace your Commodore Amiga floppy drive (plus many other makes of computers). These are generic units that simply replace your existing floppy drive or put in an external enclosure. The Gotek drive is pre flashed with FlashFloppy which allows it not only to work with the Commodore Amiga, but also Amstrad CPC computers*, Sinclair Spectrum*, Atari and DOS / IBM PC's* You will need a USB memory stick (NOT included) with your loaded ADF files. This Gotek drive will work with all Commodore Amiga computers including:
  • Amiga A500
  • Amiga A500 Plus
  • Amiga A600
  • Amiga A1200
  • Amiga A1000
  • Amiga A1500
  • Amiga A2000
  • Amiga A3000
  • Amiga A4000
  • Amiga 4000T
You can also choose from a selection of add-ons below which include
  • OLED Display instead of the 3 Digit Display
  • Internal Gotek Speaker to hear those floppy sounds!
  • Gotek Rotary knob for easily selecting that game, app or demo
  We also sell Amiga Gotek Drives with 3D printed mounts that fit neatly in your Amiga: Amiga A500 Internal Gotek Drive with OLED Display Amiga A500 Plus Gotek Drive with OLED Display Amiga A600 Internal Gotek Drive with OLED Display Amiga A1200 Internal Gotek Drive with OLED Display   What are gotek drives in detail? Read here What is FlashFloppy? Check out this link Want to know even more about them, checkout retro32.com's review of them here Also checkout one of our favorite youtube streamers TheGebs24 and her views on the Gotek drive!   *Amstrad / Spectrum or computers with 3" disk drives or old PCs with 5.25" drives and such. You just need the correct floppy IDE or Ribbon connection cables NOT INCLUDED.
 £ 29.99 Excl. VAT Read more
TF1260 TerribleFire A1200 Accelerator
TF1260 TerribleFire A1200 Accelerator – NO CPU
TF1260 TerribleFire Amiga 1200 Accelerator which hosts 64Mb Fast Ram, IDE connector (DOES NOT INCLUDE 68060 PROCESSOR). The TF1260 is one of the best 060 accelerators you can purchase for the Amiga 1200 And is the next step up after the TF1230 A1200 Accelerator add-on we sell for those that want that large speed jump. Full specs:
  • 128MByte of fast-ram.
  • IDE Interface - Driver required - ehide.device
  • Compatible with any A1200 motherboard revision.
  • Fits in your old/new stock A1200 case!!!
  • Just add your choice of 68060 processor!
  Processor support: The TF1260 TerribleFire supports all genuine 68060 processors including:
  • MC68060RC50 or XC68060RC50 (Complete with MMU & FPU)
  • MC68LC060RC50 or XC68LC060RC50 (MMU No FPU)
  • MC68EC060RC50 or XC68EC060RC50 (No MMU or FPU)
Only purchase this card if you know you have a genuine 68060 processor, The low end versions that have no MMU or FPU are more often genuine.   Prerequisites 
  • Timing fix is strongly recommended on your A1200 motherboard. We can do this free of charge if you send your board to us (return shipping does need to be covered).
  • Kickstart ROM 3.1, 3.1.4, 3.2, 3.x or 3.9 (not compatible with 3.0).
  What is Terriblefire? Well it's not what it's who, and that person is Stephen Leary who has designed a whole host of accelerators and ram cards for the Amiga A500, A1200 and Amiga CD32. These include many but the most common ones are:   NOTES:
  • For every TF1260 sold we donate a percentage of the sale to Stephen Leary to support further TF card developments and we also support our builders.
  • Timing fix is recommended on your A1200 motherboard. We can do this free of charge if you send your board to us (return shipping does need to be covered).
  • Cards sold as is, they are fully tested and a video will be shared of your card working before shipping.
  • We don't provide any advice or support for overclocking these cards, these are sold as 50Mhz. if you wish to overclock that is your choice. Heatsink and or fan required for overclocking.
 
 £ 191.66 Excl. VAT Select options
Amiga 1200 Case Black A1200.NET
Amiga 1200 Case Brand New Black
Amiga 1200 Case Brand New Black from A1200.net What's included?
  • Top case including enhancements
  • Bottom case including enhancements
  • Enhanced bottom trapdoor with extra vents.
  • Enhanced rear trapdoor + extra plastic holder DVI / VGA shaped hole.
  • Rubber feet
  • Set of screws
How are these brand new?
In 2016 840 Amiga users made it possible in supporting a Kickstarter to reproduce the Amiga 12000 case lead by Philippe Lang, the new A1200 cases are made using Injection Molding manufacturing technique to produce top and bottom shells as well as trapdoors and parts. The process implies the use of 3 new moulds, the first one is for the top shell, second mould for the bottom shell and last one for trapdoors and parts, all produced using brand new moulds.
Enhancements galore:
The Amiga community has never died and some have produced some great add-ons over the years to make sure the Amiga is still relevant and useful today as it was back in the 80's/early 90s and these cases take full advantage of that weather that's simply transferring your existing motherboard from your existing Amiga 1200 or have a luxury of installing a MiST FPGA Board. Below are few more enhancements: [accordion] [pane title="External CF Adaptor" start=open] A CF slot can be open up on the side of the A1200 case to allow easy access to what would be the CF card within the A1200 itself. [/pane] [pane title="MiST FPGA Board"] MiST is a FPGA based modern board that implements classic 16bit computers like the Commodore Amiga, Atari ST and 8bit systems like the Commodore 64, ZX-Spectrum, MSX, Atari XL/VCS, Apple II, Colecovision, Sega Master System, NES, SNES as well as Arcade machines. The primary difference between the MiST is that its NOT emulation. The new A1200 case has mounts to mount the MiST FPGA within the A1200 case. [/pane] [pane title="Raspberry PI"] Yes you can mount a Raspberry PI 2/3 within the new A1200 case with the use of the mounts already part of the case for a nice clean solution. [/pane] [pane title="Keyrah V2"] [caption id="attachment_18644" align="aligncenter" width="300"]Keyrah V2 Keyrah V2 for the Amiga 1200/600, C64, VIC 20 and C16[/caption] Keyrah V2 is an IO adaptor that allows you to use the original keyboards of the Commodore Amiga 600 and 1200, Commodore 64, VIC-20 and C-16 within their respective cases. The purpose of this you can then install a Raspberry PI which uses the original keyboard of that computer and providing 2 x D9 ports. The new Amiga 1200 case has mounts are located at middle top of bottom shell. This location make the keyboard adapter available for Raspberry Pi or MiST board. Original Amiga 1200 keyboard ribbon will fit nicely just at the right place on the keyboard adapter board. I/O connectors are accessible through rear panel I/O slots. [/pane] [/accordion]   So what are the differences between the original Commodore case and the New A1200 case?
  • The plastic is 100% UV proof to avoid case turning yellow over time.
  • Screw brass inserts in all 6 new screw towers for smooth operations. No more broken plastic clips!
  • Bottom trapdoor offers better cooling with extra vents and 3x rear trapdoors are available: Plain door, VGA hole, DVI hole, perfect for the Re-Amiga
  • Supports for: Raspberry Pi©, MiST© FPGA, Keyrah© V2 keyboard adapter, RapidRoad© DoubleUSB  and Lotharek© HxC Floppy emulator
 £ 88.33 Excl. VAT Read more
A1200 Case Grey - A1200.net
Amiga 1200 Case Brand New Grey
New Official Amiga 1200 cases from A1200.net features and enhancements!/ What's included?
  • Top case including enhancements
  • Bottom case including enhancements
  • Enhanced bottom trapdoor with extra vents.
  • Enhanced rear trapdoor + extra plastic holder DVI / VGA shaped hole.
  • Rubber feet
  • Set of screws
How are these brand new?
In 2016 840 Amiga users made it possible in supporting a Kickstarter to reproduce the Amiga 12000 case lead by Philippe Lang, the new A1200 cases are made using Injection Molding manufacturing technique to produce top and bottom shells as well as trapdoors and parts. The process implies the use of 3 new moulds, the first one is for the top shell, second mould for the bottom shell and last one for trapdoors and parts, all produced using brand new moulds.
Enhancements galore:
The Amiga community has never died and some have produced some great add-ons over the years to make sure the Amiga is still relevant and useful today as it was back in the 80's/early 90s and these cases take full advantage of that weather that's simply transferring your existing motherboard from your existing Amiga 1200 or have a luxury of installing a MiST FPGA Board. Below are few more enhancements: [accordion] [pane title="External CF Adaptor" start=open] A CF slot can be open up on the side of the A1200 case to allow easy access to what would be the CF card within the A1200 itself. [/pane] [pane title="MiST FPGA Board"] MiST is a FPGA based modern board that implements classic 16bit computers like the Commodore Amiga, Atari ST and 8bit systems like the Commodore 64, ZX-Spectrum, MSX, Atari XL/VCS, Apple II, Colecovision, Sega Master System, NES, SNES as well as Arcade machines. The primary difference between the MiST is that its NOT emulation. The new A1200 case has mounts to mount the MiST FPGA within the A1200 case. [/pane] [pane title="Raspberry PI"] Yes you can mount a Raspberry PI 2/3 within the new A1200 case with the use of the mounts already part of the case for a nice clean solution. [/pane] [pane title="Keyrah V2"] [caption id="attachment_18644" align="aligncenter" width="300"]Keyrah V2 Keyrah V2 for the Amiga 1200/600, C64, VIC 20 and C16[/caption] Keyrah V2 is an IO adaptor that allows you to use the original keyboards of the Commodore Amiga 600 and 1200, Commodore 64, VIC-20 and C-16 within their respective cases. The purpose of this you can then install a Raspberry PI which uses the original keyboard of that computer and providing 2 x D9 ports. The new Amiga 1200 case has mounts are located at middle top of bottom shell. This location make the keyboard adapter available for Raspberry Pi or MiST board. Original Amiga 1200 keyboard ribbon will fit nicely just at the right place on the keyboard adapter board. I/O connectors are accessible through rear panel I/O slots. [/pane] [/accordion]   So what are the differences between the original Commodore case and the New A1200 case?
  • The plastic is 100% UV proof to avoid case turning yellow over time.
  • Screw brass inserts in all 6 new screw towers for smooth operations. No more broken plastic clips!
  • Bottom trapdoor offers better cooling with extra vents and 3x rear trapdoors are available: Plain door, VGA hole, DVI hole, perfect for the Re-Amiga
  • Supports for: Raspberry Pi©, MiST© FPGA, Keyrah© V2 keyboard adapter, RapidRoad© DoubleUSB  and Lotharek© HxC Floppy emulator
 £ 137.49 Excl. VAT Select options
PiStorm32-Lite Rear Panel HDMI - USB & SD Card Slot
PiStorm32-Lite Rear Panel HDMI – USB – SD
PiStorm32-Lite Rear Panel which provides easy access to the internal PiStorm32-Lite HDMI, USB and SD card slot, negates the need to open up the A1200 trapdoor and access the SD card when updates are released.
The panel is 3D printed and available in:
  • White
  • Black
  • Gray
When purchasing, leave a note of the colour required.   Whats included:
  • Rear Panel
  • Micro HDMI Extension Cable
  • MicroSD Extension Cable
  • USB Extension Cable
  • M3 Screw and nut
  This is for the Pistorm32-Lite with Raspberry Pi3A+   Checkout the other great work the developer has created here  
 £ 33.33 Excl. VAT Add to basket
Re-Amiga A1200 Build Service
ReAmiga A1200 Refurbished Fully Built
ReAmiga A1200 Rev 1.5 Refurbishment Service built using an A1200 board the customer supplies as a donor*. The Re-Amiga A1200 is a reverse engineered board by John "Chucky" Hertell. and is a full A1200 board with some extras added which include:
  • Composite Video area changed to a new decoder for improved quality.
  • VGA Connector added, VGA monitor needs to support 15Khz!
  • S-Video Connector for S-Video Out
  • Kickstart switch built in, if you are using 27C800 Eproms. you can program one bank with one kickstart and the other bank with another.
  • PCMCIA Reset fix.
  • Optional IRQ7 Switch.
  • Native PAL or NTSC Option (below)
  • Added LED's for _RST, _KB_RST, _ODD_CIA, _EVEN_CIA and _ROMEN also to Serial TXD and RXD (from the 5V level).
  • Added resistor to IDE Activity so now adapters that made IDE led always bright will be handled correctly.
  • Added pads close to floppy connector for a 0Ohm resistor if you want to do the Escom floppy patch instead of a wire.
  • 9 Pin Mouse Port
  • Fits in your current metal shielding**
  This is a build service using a donor board you provide or provide the needed parts to complete the build. We are able to provide a donor board if required, ask for further details.    Once ordered we will request a 10% deposit to secure the service and send the you the address where to send you A1200 donor board.   * Custom chips will be tested before hand, any custom chips which are faulty we will contact you and send a quote for the any faulty chips or parts. ** ReAmiga board does not come with any metal shielding.  
We reserve the right to cancel and refund any deposit made if we find an issues with securing any component or costs have increased to a level where building a unit becomes unaviable.
   
 £ 699.99 Excl. VAT Add to basket
Amiga 1200 Case Translucent A1200.NET
Amiga 1200 Case Brand New Translucent
Amiga 1200 Case Brand New Translucent from A1200.net. What's included?
  • Top case including enhancements
  • Bottom case including enhancements
  • Enhanced bottom trapdoor with extra vents.
  • Enhanced rear trapdoor + extra plastic holder DVI / VGA shaped hole.
  • Rubber feet
  • Set of screws
How are these brand new?
In 2016 840 Amiga users made it possible in supporting a Kickstarter to reproduce the Amiga 12000 case lead by Philippe Lang, the new A1200 cases are made using Injection Molding manufacturing technique to produce top and bottom shells as well as trapdoors and parts. The process implies the use of 3 new moulds, the first one is for the top shell, second mould for the bottom shell and last one for trapdoors and parts, all produced using brand new moulds.
Enhancements galore:
The Amiga community has never died and some have produced some great add-ons over the years to make sure the Amiga is still relevant and useful today as it was back in the 80's/early 90s and these cases take full advantage of that weather that's simply transferring your existing motherboard from your existing Amiga 1200 or have a luxury of installing a MiST FPGA Board. Below are few more enhancements: [accordion] [pane title="External CF Adaptor" start=open] A CF slot can be open up on the side of the A1200 case to allow easy access to what would be the CF card within the A1200 itself. [/pane] [pane title="MiST FPGA Board"] MiST is a FPGA based modern board that implements classic 16bit computers like the Commodore Amiga, Atari ST and 8bit systems like the Commodore 64, ZX-Spectrum, MSX, Atari XL/VCS, Apple II, Colecovision, Sega Master System, NES, SNES as well as Arcade machines. The primary difference between the MiST is that its NOT emulation. The new A1200 case has mounts to mount the MiST FPGA within the A1200 case. [/pane] [pane title="Raspberry PI"] Yes you can mount a Raspberry PI 2/3 within the new A1200 case with the use of the mounts already part of the case for a nice clean solution. [/pane] [pane title="Keyrah V2"] [caption id="attachment_18644" align="aligncenter" width="300"]Keyrah V2 Keyrah V2 for the Amiga 1200/600, C64, VIC 20 and C16[/caption] Keyrah V2 is an IO adaptor that allows you to use the original keyboards of the Commodore Amiga 600 and 1200, Commodore 64, VIC-20 and C-16 within their respective cases. The purpose of this you can then install a Raspberry PI which uses the original keyboard of that computer and providing 2 x D9 ports. The new Amiga 1200 case has mounts are located at middle top of bottom shell. This location make the keyboard adapter available for Raspberry Pi or MiST board. Original Amiga 1200 keyboard ribbon will fit nicely just at the right place on the keyboard adapter board. I/O connectors are accessible through rear panel I/O slots. [/pane] [/accordion]   So what are the differences between the original Commodore case and the New A1200 case?
  • The plastic is 100% UV proof to avoid case turning yellow over time.
  • Screw brass inserts in all 6 new screw towers for smooth operations. No more broken plastic clips!
  • Bottom trapdoor offers better cooling with extra vents and 3x rear trapdoors are available: Plain door, VGA hole, DVI hole, perfect for the Re-Amiga
  • Supports for: Raspberry Pi©, MiST© FPGA, Keyrah© V2 keyboard adapter, RapidRoad© DoubleUSB  and Lotharek© HxC Floppy emulator
 £ 88.33 Excl. VAT Read more
GoDrive1200 Gotek A1200 A500
GoDrive1200 Gotek for Amiga A1200 and A500
GoDrive1200 Gotek for Amiga A1200 and A500 is an upgrade that provides you both the use of your current internal floppy drive in the A1200 and A500 and also have access to a Gotek drive, so have the best of both worlds floppy drive and Gotek drive.   Features:
  • Large 1.3” OLED screen
  • Rotary encoder with switch
  • Activity LED light
  • Drive selector
  • USB socket
  • FlashFloppy Firmware
The unit requires no cutting of the case!!   Notes: Compatible with all Amiga 1200 units however there are exceptions as the A1200 came with different makes of floppy drive so if you have:
  • Mitsumi D357T2,
  • TEAC FD-235HF,
  • Panasonic JU-253-043P
Please ask for a SLIM version, as these drives are too long to fit standard GoDRIvE1200 model. Escom Amiga 1200 If you are owner of ESCOM A1200, GoDRIvE1200 will not work without modifying mainboard and replacing PC-compatible FDD fitted, for Amiga compatible one. There is a wire underneath the floppy connector that is bridging Pin 2 and Pin 34, this simply needs cutting out or de soldered.    
 £ 95.83 Excl. VAT Read more